Crankshaft Timing Ring - Remove and Install
开始:
- 拆下曲轴。 有关正确步骤,请参阅拆解和组装, "曲轴 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将曲轴 (1) 支撑在适当的台架上。
- 将六角头螺钉 (2) 从曲轴正时齿圈 (3) 上拆下。 不要重复使用六角螺钉。
- 小心地将曲轴正时齿圈 (3) 从曲轴 (1) 上卸下。 不要重复使用曲轴正时齿圈。
注: 拆卸曲轴正时齿圈时,确保不损坏曲轴的密封表面 (4) 。
注: 除非定位销损坏,否则不要将定位销 (5) 从曲轴 (1) 上卸下。
Show/hide table
图 1 | g01341462 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保曲轴上曲轴正时齿圈的法兰清洁且无损坏。
- 将曲轴 (1) 支撑在适当的台架上。
Show/hide table
图 2 g01341462 - 如果定位销 (5) 已拆下,将新定位销安装到曲轴 (1) 上。
- 将新曲轴正时齿圈 (3) 定位在曲轴上,使轮齿朝向曲轴臂。 对齐曲轴正时齿圈 (3) 上的孔与曲轴上的定位销 (5)。 小心地将曲轴正时齿圈 (3) 安装到曲轴 (1) 上。
注: 安装曲轴正时齿圈时,确保不损坏曲轴的密封表面 (4) 。
- 安装新六角头螺钉 (2)。 拧紧六角头螺钉至扭矩为
15 N·m (133 lb in) 。
结束:
- 安装曲轴。 有关正确步骤,请参阅拆解和组装, "曲轴 - 安装"。
Caterpillar Information System:
C7.1 Engines Crankshaft Rear Seal - Remove
C7.1 Engines Crankshaft Rear Seal - Install
C7.1 Engines Crankshaft Position Sensor - Remove and Install
C7.1 Engines Crankshaft Main Bearings - Remove and Install - Crankshaft in Position
C7.1 Engines Crankshaft Gear - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install
C7.1 Engines Crankshaft Front Seal - Remove and Install - Crankshaft Front Seal for Heavy Duty Front Cover
C7.1 Engines Crankshaft - Remove
C7.1 Engines Crankshaft - Install
C7.1 Engines Crankcase Breather - Remove - Unfiltered Breather
C7.1 Engines Crankcase Breather - Install - Unfiltered Breather
C7.1 Engines Crankcase Breather - Remove - Filtered Breather
C7.1 Engines Cylinder Head - Install
C7.1 Engines Cylinder Head - Remove
C7.1 Engines ECM Mounting Bracket - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Electronic Control Module - Remove and Install
349F and 352F Excavators Machine System Specifications Track
C280-16 Engine Fluid Recommendations
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
C7.1 Engines Electronic Unit Injector - Install
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base