Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M8 x 50 mm |
2 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
确保导线线束布线正确,且电缆带未过分拧紧。 过分拧紧电缆带会损坏导线线束卷。 |
- 必要时,遵循步骤 1.a 至 1.d 组装发动机机油冷却器 (5)。
- 确保发动机机油冷却器基体 (10) 清洁、无损坏和堵塞。 如果发动机机油冷却器基体 (10) 损坏或堵塞,则进行更换。
- 确保隔板 (11) 清洁且无损坏。 如果隔板 (11) 损坏,则进行更换。
- 将新密封垫 (10) 定位在隔板 (17) 上。 将发动机机油冷却器基体 (9) 安装到隔板上。
- 安装螺栓 (8) 并用手拧紧。
Show/hide table图 2 g03408908 Show/hide table图 3 g03408917 - 清洁缸体密封垫表面。
- 将工具 (A) 安装到位置 (B) 中。
- 将新密封垫 (7)(未显示)定位到工具 (A) 上。 确保密封垫朝向正确。
- 将发动机机油冷却器组件 (5) 安装到缸体上。
- 将螺栓 (6) 安装到发动机机油冷却器 (5) 上,用手拧紧。 安装螺栓时,应支承发动机机油冷却器。
注: 确保不同长度的螺栓安装在正确位置中。
- 拆下工具 (A),并安装剩余螺栓 (6)。
Show/hide table
图 4 g03408818 - 如果发动机有左手侧低位安装机油滤清器 (1),安装机油滤清器底座。 有关正确的步骤,请参阅拆解和组装, "机油过滤器底座 - 拆卸和安装"。
- 如果发动机有右手侧机油滤清器,遵循步骤 9.a 至 9.d 安装护板 (2)。
- 将螺栓 (4) 安装到护板 (2) 上。
- 将新密封垫 (3)(未显示)定位到护板 (2) 上。
- 将护板组件 (2) 安装到发动机机油冷却器组件上。
- 拧紧螺栓 (4) 至扭矩为
22 N·m (195 lb in) 。
Show/hide table图 5 g03408914 带护板或低位安装滤清器底座的发动机机油冷却器的拧紧顺序 - 按照图 5 所示的顺序,拧紧螺栓至扭矩为
22 N·m (195 lb in) 。 - 加注冷却系统至正确液位。 有关正确的步骤,请参阅操作和保养手册, "冷却系统冷却液 - 更换"。
- 检查发动机润滑油油位。 有关正确的步骤,参考操作和保养手册, "发动机机油油位 - 检查"。
Show/hide table
图 1 | g03408820 |
结束:
- 安装电子控制模块(ECM)的安装支架。 有关正确步骤,请参阅拆解和组装, "ECM 安装支架 - 拆卸和安装"。
Caterpillar Information System:
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Electronic Unit Injector - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
C280-16 Engine Fluid Recommendations
349F and 352F Excavators Machine System Specifications Track
C7.1 Engines Electronic Control Module - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines ECM Mounting Bracket - Remove and Install
C7.1 Engines Cylinder Head - Remove
C7.1 Engines Cylinder Head - Install
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Filter Base - Remove and Install
C7.1 Engines Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Engines Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Engines Engine Oil Pressure Sensor - Remove and Install
C7.1 Engines Engine Oil Pump - Install
C7.1 Engines Engine Oil Pump - Remove
C7.1 Engines Exhaust Elbow - Remove and Install
C7.1 Engines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C7.1 Engines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C7.1 Engines Fan - Remove and Install