Exhaust Elbow - Remove and Install
开始:
- 拆下原始以设备制造商(OEM)排气系统。 有关正确步骤,请参阅(OEM)信息。
Show/hide table
图 1 | g03409852 |
- 拆下将排气弯头 (3) 固定到发动机上的螺栓 (4)。 将排气弯头 (3) 从发动机上拆下。
- 拆下将排气弯头 (3) 连接到涡轮增压器 (5) 的连接器 (1)。
- 如有必要,将螺柱 (2) 从排气弯头 (3) 上拆下。
Show/hide table
图 2 | g03409852 |
- 彻底清洁排气弯头 (3)、连接器 (1) 和涡轮增压器 (5) 的出口。 检查部件的密封表面有无磨损或损坏。 更换任何损坏或磨损的部件。
- 如有必要,将螺柱 (2) 安装到排气弯头 (3) 上。 拧紧螺柱至扭矩
18 N·m (159 lb in) 。 - 将连接器 (1) 安装到排气弯头 (3) 上。
- 将连接器 (1) 与涡轮增压器 (5) 的出口对准。 将连接器 (1) 和排气弯头 (3) 的组件安装到涡轮增压器 (5) 上。
- 用手安装并拧紧螺栓 (4)。
- 确保连接器 (1) 与涡轮增压器 (5) 的出口和排气弯头 (3) 完全接合。 确保涡轮增压器和排气弯头之间的间隙等距。
- 拧紧螺栓 (4) 至扭矩为
44 N·m (32 lb ft) 。
结束:
- 安装原始以设备制造商(OEM)排气系统。 有关正确步骤,请参阅(OEM)信息。
Caterpillar Information System:
C7.1 Engines Engine Oil Pump - Remove
C7.1 Engines Engine Oil Pump - Install
C7.1 Engines Engine Oil Pressure Sensor - Remove and Install
C7.1 Engines Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Engines Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Engines Engine Oil Filter Base - Remove and Install
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Electronic Unit Injector - Install
C7.1 Engines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C7.1 Engines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C7.1 Engines Fan - Remove and Install
C7.1 Engines Fan Drive - Remove and Install
C7.1 Engines Flow Control Valve - Remove and Install
C7.1 Engines Flywheel - Install - Equipped with Rear Power Take-Off
C7.1 Engines Flywheel - Install
C7.1 Marine Engine Engine Oil Filter Base - Remove and Install - Non M.C.S. Arrangement
C7.1 Engines Flywheel - Remove - Equipped with Rear Power Take-Off
C7.1 Engines Flywheel - Remove
C7.1 Engines Flywheel Housing - Remove and Install - Type A and Type B Wet Back End Housing
C7.1 Engines Flywheel Housing - Remove and Install - Flywheel Housing that is Equipped with Rear Power Take-Off