Engine Oil Filter Base - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 1U-8760 | 链式扳手 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检查, 保养, 测试, 调整 and 维修发动机时,务必留心,确保将溢出的液体盛装在容器中。在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 将适当的容器放置到发动机机油滤清器 (5) 的下方,用来盛装所有可能溢出的机油。
- 使用工具 (A),拆下发动机机油滤清器 (5)。 有关正确的步骤,请参阅操作和保养手册, "发动机机油和滤清器 - 更换"。
- 拆下螺栓 (3 )。
注: 如果安装了不同长度的螺栓,确定螺栓的正确位置。
- 拆下发动机机油滤清器底座 (4)。
- 拆下密封垫 (6)。
- 如有必要,将螺塞 (1) 从发动机机油滤清器底座 (4) 上拆下。 将 O 形密封圈 (2) 从螺塞 (1) 上拆下。
Show/hide table
图 1 | g01980935 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁发动机机油滤清器底座 (4)。 清洁缸体或发动机机油冷却器的密封垫表面。
- 必要时,将新的 O 型密封圈 (2) 安装到螺塞 (1) 上。 将螺塞 (1) 安装到发动机机油滤清器底座 (4) 上。 拧紧螺塞至扭矩为
12 N·m (106 lb in) 。 - 将螺栓 (3) 安装到发动机机油滤清器底座 (4) 上。
- 将密封垫 (6) 安装到螺栓 (3) 上。 将发动机机油滤清器底座安装到缸体或发动机机油冷却器上。
- 拧紧螺栓 (3) 至扭矩为
22 N·m (195 lb in) 。 - 安装新发动机机油滤清器 (5) 并检查发动机润滑油油位。 有关正确的步骤,参考操作和保养手册, "发动机机油油位 - 检查"。
Show/hide table
图 2 | g01980935 |
Caterpillar Information System:
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Electronic Unit Injector - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
C280-16 Engine Fluid Recommendations
349F and 352F Excavators Machine System Specifications Track
C7.1 Engines Electronic Control Module - Remove and Install
C7.1 Engines Electric Starting Motor - Remove and Install
C7.1 Engines Engine Oil Pan - Install - Aluminum Oil Pan
C7.1 Engines Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Engines Engine Oil Pressure Sensor - Remove and Install
C7.1 Engines Engine Oil Pump - Install
C7.1 Engines Engine Oil Pump - Remove
C7.1 Engines Exhaust Elbow - Remove and Install
C7.1 Engines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C7.1 Engines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C7.1 Engines Fan - Remove and Install
C7.1 Engines Fan Drive - Remove and Install
C7.1 Engines Flow Control Valve - Remove and Install
C7.1 Engines Flywheel - Install - Equipped with Rear Power Take-Off