Engine Oil Pan - Install - Aluminum Oil Pan
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | 导向螺柱 M8 x 100 mm |
4 |
B | 6V-6640 | 密封胶 | - |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 按照本地法规和指令处置所有液体。 |
- 必要时,遵循步骤 1.a 至步骤 1.c 将机油油位开关 (12) 安装到发动机油底壳 (9) 上。
- 将新的 O 形密封圈 (13) 安装到机油油位开关 (12) 上。
- 将机油油位开关 (12) 安装到发动机油底壳 (9) 上。 拧紧机油油位开关至扭矩为
34 N·m (301 lb in) 。 - 将新电缆带 (14) 安装到机油油位开关 (12) 的线束组件上。
注: 确保电缆带符合 OEM 技术规格。
Show/hide table图 2 g02010373 Show/hide table图 3 g03409387 - 确保缸体密封垫表面清洁、无损坏。
- 将工具 (A) 安装到缸体中的位置 (X)。
- 确保发动机油底壳 (9) 清洁、无损坏。
- 将新密封垫 (8) 放置在发动机油底壳 (9) 上。
- 将发动机油底壳组件 (9) 与工具 (A) 对齐。 将发动机油底壳组件安装到缸体中。
- 将螺栓 (10) 安装到发动机油底壳 (9) 上,用手拧紧。 安装螺栓时,支承发动机油底壳。
- 拆下工具 (A),然后安装其余螺栓 (10),用手拧紧。
- 将新螺栓 (11) 安装到发动机油底壳 (9) 上,用手拧紧。
Show/hide table
图 4 g03409407 - 拧紧螺栓 (10) 和螺栓 (11) 至扭矩为
22 N·m (195 lb in) 。 按照图 4 中所示的顺序拧紧螺栓。Show/hide table图 5 g03409386 - 将新的 O 形密封圈 (3) 安装到排放塞 (2) 上。 将排放螺塞 (2) 安装到发动机油底壳上。 拧紧机油排放塞至扭矩为
34 N·m (301 lb in) 。 - 如有必要,遵循步骤 12.a 至步骤 12.c,安装油尺管组件 (4)。
- 将新密封 (6) 安装到管组件 (4) 上。
- 将工具 (B) 涂敷在螺母 (5) 上。 将管组件安装到发动机油底壳上。
注: 确保管组件的方位正确。
- 拧紧螺母 (5) 至扭矩为
18 N·m (159 lb in) 。
- 加注发动机油底壳至正确油位。 请参阅操作和保养手册, "机油滤清器更换"以了解正确程序。
Show/hide table
图 1 | g03409388 |
Caterpillar Information System:
C7.1 Engines Engine Oil Filter Base - Remove and Install
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Remove - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a Low Mounted Filter Base
C7.1 Engines Engine Oil Cooler - Install - Engine Oil Cooler with a High Mounted Filter Base
C7.1 Engines Electronic Unit Injector - Remove
C7.1 Engines Electronic Unit Injector - Install
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies Internal Component Preremoval Steps (Input/Output Cabinet)
UPS1000Z, UPS1200Z, UPS500G and UPS600G Uninterruptible Power Supplies General Information (Input/Output Cabinet)
C280-16 Engine Fluid Recommendations
349F and 352F Excavators Machine System Specifications Track
C7.1 Engines Electronic Control Module - Remove and Install
C7.1 Engines Engine Oil Pan - Remove - Aluminum Oil Pan
C7.1 Engines Engine Oil Pressure Sensor - Remove and Install
C7.1 Engines Engine Oil Pump - Install
C7.1 Engines Engine Oil Pump - Remove
C7.1 Engines Exhaust Elbow - Remove and Install
C7.1 Engines Exhaust Manifold - Remove and Install - Side Mounted Exhaust Manifold
C7.1 Engines Exhaust Manifold - Remove and Install - Top Mounted Exhaust Manifold
C7.1 Engines Fan - Remove and Install
C7.1 Engines Fan Drive - Remove and Install
C7.1 Engines Flow Control Valve - Remove and Install
C7.1 Engines Flywheel - Install - Equipped with Rear Power Take-Off
C7.1 Engines Flywheel - Install