Cylinder Block
Show/hide table
| |
| Illustration 1 | g03276016 |
|
Front view of engine | |
Show/hide table
| Specification for 352-5509 Cylinder Block Gp | |||
| Item | Qty | Part | Specification Description |
| During assembly, bottom of the plate, top of the block, and both the sides of the gasket plate must be free of all visible fuel, oil, water and gasket adhesives, assembly compounds, or any other contaminates. | |||
| 1 | 4 | 4W-4813 Plug | Torque to |
| 2 | 4 | 5F-9657 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 3 | 22 | 101-1198 Camshaft Bearing | The camshaft bearing joint must be on the horizontal centerline of the bore |
| The upper oil holes must be positioned at an angle (C) of 20 ± 5 degrees above the horizontal centerline of the bore. The lower oil hole of the camshaft bearing should be 20 ± 5 degrees below the horizontal centerline of the bore. . | |||
| After installation, bore is |
|||
| A | 40 | 8T-0099 Dowel | Extension of the dowel from the top face of the cylinder block is |
| B | 20 | 197-7008 Dowel | Extension of the dowel from the top face of the cylinder block is |
| 4 | 8 | 6V-3348 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 5 | 2 | 5P-8210 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| D | - | - | New dimension from centerline of crankshaft bearing bore to bottom of cylinder block (pan rails) is |
| E | - | - | Bore in the cylinder block for the main bearings is |
Show/hide table
| |
| Illustration 2 | g03276017 |
|
Right side view | |
Show/hide table
| Item | Qty | Part | Specification Description |
| 6 | 3 | 7N-2047 Dowel | Extension (F) of the dowel is |
| 7 | 3 | 7X-4805 O-Ring Seal | Before assembly, lubricate the bore lightly with the lubricant that is being sealed. |
| 8 | 2 | 7N-2044 Dowel | Extension (G) of the dowel is |
Show/hide table
| |
| Illustration 3 | g03276018 |
Show/hide table
| Item | Qty | Part | Specification Description |
| 9 | 20 | 352-6061 Liner Seal | Assemble liner seals dry on clean and dry liner grooves.
Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 10 | 60 | 7N-2046 O-Ring Seal | Before assembly, cover seals with either P-80 Rubber Lubricant Emulsion or liquid soap. |
| 11 | 11 | 223-1696 Crankshaft Bearing Cap | Width of the crankshaft bearing cap is Width (H) in the cylinder block for crankshaft bearing cap is |
| J | - | - | New dimension from centerline of crankshaft bearing bore to the top of the cylinder block is |
| 12 | 44 | 7X-7925 Bolt | Use the following procedure in order to tighten the crankshaft bearing cap bolts: Install main bearing caps with the part number and FRONT toward the front of the block. Each cap has a number. Each cap must be installed in the same position as the correct number on the side of the cylinder block pan rail. 1. Before assembly, lubricate the threads completely with clean engine oil. 2. Hand tighten bolts in the tapped holes. 3. Tighten bolts in the numerical sequence as shown in Illustration 3 to 4. Again, tighten each bolt to an additional angle of 180 ± 5 degrees. |
Caterpillar Information System:
C32 Marine Engines Heat Exchanger - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Remove and Install
C175-16 Generator Set Engine Engine Oil Filter Housing - Remove and Install
C175-16 Generator Set Engine Engine Oil Pump - Assemble
2012/11/09 A New Canadian Standards Association (CSA) Ignition Harness Is Used by Certain G3406 Engines {1408}
2012/10/04 A New Unit Injector Wiring Group Is Used on Certain C9.3 Industrial Engines {1290, 1408, 1900}
C175-16 Generator Set Engine Engine Oil Pump - Disassemble
C175-16 Generator Set Engine Engine Oil Pump - Remove and Install
C32 Marine Engines Bearing Clearance - Check
2012/10/04 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1067}
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
G3520E Generator Set Engines Water Lines
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Assemble
C175-16 Generator Set Engine Engine Oil Screen - Remove and Install
C175-16 Generator Set Engine Engine Oil Pan - Remove and Install
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Worksheet
2012/10/30 A New Pressure Relief Valve for the Fuel Rail Group Is Used in Certain C9.3 Industrial Engines {1288}
2012/10/11 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}