Customer Specified Parameters Worksheet
Show/hide table
| Customer Specified Parameters Worksheet | |
|---|---|
| Speed Control | |
| Low Idle Speed | |
| High Idle Speed | |
| Engine Acceleration Rate | |
| Engine Speed Decelerating Ramp Rate | |
| Throttle Selection Status | |
| Throttle Position #1 Engine Speed | |
| Throttle Position #2 Engine Speed | |
| Throttle Position #3 Engine Speed | |
| Throttle Position #4 Engine Speed | |
| Throttle #1 Engine Speed Droop | |
| Throttle #2 Engine Speed Droop | |
| Data Link Engine Speed Droop | |
| Throttle Parameters | |
| Number of Throttles | |
| Throttle Arbitration Method | |
| Throttle 1 Idle Validation Switch Enable Status | |
| Throttle 2 Idle Validation Switch Enable Status | |
| Throttle #1 Idle Validation Switch Lower Limit Voltage | |
| Throttle #2 Idle Validation Switch Lower Limit Voltage | |
| Throttle #1 Idle Validation Switch Upper Limit Voltage | |
| Throttle #2 Idle Validation Switch Upper Limit Voltage | |
| Throttle #1 Voltage Low Diagnostic Threshold | |
| Throttle #1 Low Idle Position Voltage | |
| Throttle #1 High Idle Position Voltage | |
| Throttle #1 Voltage High Diagnostic Threshold | |
| Throttle #2 Voltage Low Diagnostic Threshold | |
| Throttle #2 Low Idle Position Voltage | |
| Throttle #2 High Idle Position Voltage | |
| Throttle #2 Voltage High Diagnostic Threshold | |
| Limp Home Desired Engine Speed | |
| Limp Home Engine Speed Ramp Rate | |
| Miscellaneous | |
| Monitoring Mode Shutdowns | |
| Engine Location | |
| Automatic Idle Kickdown Enable Status | |
| Automatic Idle Kickdown Delay Time | |
| Automatic Idle Kickdown Enable Switch Configuration | |
| Automatic Idle Kickdown Deactivation Engine Speed Ramp Rate | |
| Automatic Idle Kickdown Activation Engine Speed Ramp Rate | |
| Fuel Pump Actuator Calibration Code | |
| Governor Gain | |
| J1939 Continuous Fault Handling | |
| Remote Torque Speed Control Enable Status | |
Caterpillar Information System:
C175-16 Generator Set Engine Engine Oil Pan - Remove and Install
C175-16 Generator Set Engine Engine Oil Screen - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Assemble
G3520E Generator Set Engines Water Lines
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
G3520E Generator Set Engines Cylinder Block
C32 Marine Engines Heat Exchanger - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
2012/10/30 A New Pressure Relief Valve for the Fuel Rail Group Is Used in Certain C9.3 Industrial Engines {1288}
2012/10/11 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
2012/10/15 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
C13, C15, and C18 Tier 4 Final Engines DEF Control Module Power - Test
C13, C15, and C18 Tier 4 Final Engines NOx Conversion Is Low
C13, C15, and C18 Tier 4 Final Engines SCR Catalyst Inlet Temperature Sensor - Test
3500 Generator Sets with Dynamic Gas Blending Fluid Recommendations
2012/10/08 An Improved Hand Operated Fuel Priming Pump Is Available {1258}
3500 Generator Sets with Dynamic Gas Blending Starting the Engine - Natural Gas
2012/10/08 An Improved Hand Operated Fuel Priming Pump Is Available {1258}
C32 Marine Engines Electric Starting Motor - Remove and Install
2012/10/11 Correction to Part Numbers Specific to Generator Arrangement for Certain XQ80 and XQ100 Rental Generator Sets {4450}