Customer Specified Parameters Table
Show/hide table
Customer Specified Parameters | ||
---|---|---|
ECM Parameter | Possible Values | Default Value |
Speed Control | ||
Low Idle Speed | Dependent on engine rating | - |
High Idle Speed | Dependent on engine rating | - |
Engine Acceleration Rate | 0 to 2000 rpm/sec | 1000 rpm/sec |
Engine Speed Decelerating Ramp Rate | 0 to 2000 rpm/sec | 1000 rpm/sec |
Throttle Selection Status | Continuous Throttle
Multi-Position Throttle |
Continuous Throttle |
Throttle Position #1 Engine Speed | 800 to 3300 rpm | 1500 rpm |
Throttle Position #2 Engine Speed | 800 to 3300 rpm | 1600 rpm |
Throttle Position #3 Engine Speed | 800 to 3300 rpm | 1700 rpm |
Throttle Position #4 Engine Speed | 800 to 3300 rpm | 1800 rpm |
Throttle #1 Engine Speed Droop | 0 to 8 percent | 7 percent |
Throttle #2 Engine Speed Droop | 0 to 8 percent | 7 percent |
Data Link Engine Speed Droop | 0 to 8 percent | 7 percent |
Throttle Parameters | ||
Number of Throttles | 0-2 | 0 |
Throttle Arbitration Method | Largest Wins
Lowest Wins Manual Manual with Pre-condition |
Largest Wins |
Throttle 1 Idle Validation Switch Enable Status | Enabled
Disabled |
Enabled |
Throttle 2 Idle Validation Switch Enable Status | Enabled
Disabled |
Enabled |
Throttle #1 Idle Validation Switch Lower Limit Voltage | 0.4 to 1.6 VDC | 1.0 VDC |
Throttle #2 Idle Validation Switch Lower Limit Voltage | 0.4 to 1.6 VDC | 1.0 VDC |
Throttle #1 Idle Validation Switch Upper Limit Voltage | 0.4 to 1.6 VDC | 1.2 VDC |
Throttle #2 Idle Validation Switch Upper Limit Voltage | 0.4 to 1.6 VDC | 1.2 VDC |
Throttle #1 Voltage Low Diagnostic Threshold | 0 to 1.6 VDC | 0.4 VDC |
Throttle #1 Low Idle Position Voltage | 0.4 to 1.6 VDC | 0.6 VDC |
Throttle #1 High Idle Position Voltage | 3.6 to 4.6 VDC | 4.0 VDC |
Throttle #1 Voltage High Diagnostic Threshold | 3.6 to 5.0 VDC | 4.5 VDC |
Throttle #2 Voltage Low Diagnostic Threshold | 0 to 1.6 VDC | 0.4 VDC |
Throttle #2 Low Idle Position Voltage | 0.4 to 1.6 VDC | 0.6 VDC |
Throttle #2 High Idle Position Voltage | 3.6 to 4.6 VDC | 4.0 VDC |
Throttle #2 Voltage High Diagnostic Threshold | 3.6 to 5.0 VDC | 4.5 VDC |
Limp Home Desired Engine Speed | 800 to 2000 rpm | 1200 rpm |
Limp Home Engine Speed Ramp Rate | 0 to 2000 rpm/sec | 1000 rpm/sec |
Miscellaneous | ||
Monitoring Mode Shutdowns | Enabled
Disabled |
Enabled |
Engine Location | Engine #1
Engine #2 |
Engine #1 |
Automatic Idle Kickdown Enable Status | Disabled
Enabled |
Disabled |
Automatic Idle Kickdown Delay Time | 0 to 6550 secs | 3 secs |
Automatic Idle Kickdown Enable Switch Configuration | Not Installed
Normally Closed (To Ground) Normally Open |
Not Installed |
Automatic Idle Kickdown Deactivation Engine Speed Ramp Rate | 0 to 2000 rpm/sec | 1000 rpm/sec |
Automatic Idle Kickdown Activation Engine Speed Ramp Rate | 0 to 2000 rpm/sec | 1000 rpm/sec |
Fuel Pump Actuator Calibration Code | AxxxBxxxCxxx | AxxxBxxxCxxx |
Governor Gain | 50%, 75%, 100% ,150%, or 200% of Factory Gain | 100% of Factory Gain |
J1939 Continuous Fault Handling | ||
Remote Torque Speed Control Enable Status | Enabled
Disabled |
Disabled |
Caterpillar Information System:
G3520E Generator Set Engines Cylinder Block
C32 Marine Engines Heat Exchanger - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Remove and Install
C175-16 Generator Set Engine Engine Oil Filter Housing - Remove and Install
C175-16 Generator Set Engine Engine Oil Pump - Assemble
2012/11/09 A New Canadian Standards Association (CSA) Ignition Harness Is Used by Certain G3406 Engines {1408}
2012/10/04 A New Unit Injector Wiring Group Is Used on Certain C9.3 Industrial Engines {1290, 1408, 1900}
C175-16 Generator Set Engine Engine Oil Pump - Disassemble
C175-16 Generator Set Engine Engine Oil Pump - Remove and Install
C32 Marine Engines Bearing Clearance - Check
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
G3520E Generator Set Engines Water Lines
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Assemble
C175-16 Generator Set Engine Engine Oil Screen - Remove and Install
C175-16 Generator Set Engine Engine Oil Pan - Remove and Install
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Worksheet
2012/10/30 A New Pressure Relief Valve for the Fuel Rail Group Is Used in Certain C9.3 Industrial Engines {1288}
2012/10/11 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}
2012/10/15 Later Pre-Chamber Cylinder Heads On Early 3304 Engines Without Drilled Rocker Stands Are Used {1100}