A New Unit Injector Wiring Group Is Used on Certain C9.3 Industrial Engines {1290, 1408, 1900}
- Industrial Engine:
- C9.3 (S/N: C9N1-UP; D9N1-UP)
Description of Change: A new unit injector wiring harness is now available for Tier 4i C9.3 Industrial Engines. The new harness incorporates a protective sleeve on the exposed section of wiring connecting to the fuel injector to provide added protection against abrasion. Refer to Illustration 1.
Show/hide table
Illustration 1 | g03206556 |
(1) Location of protective sleeve |
Adaptable To: The new unit injector wiring group replaces the existing wiring group on the serial numbers listed above. Refer to Table 1 for a list of the new part numbers and the part numbers that are being replaced.
Show/hide table
New Part Number     | Former Part Number     |
399-4012     | 353-5939     |
399-4009     | 353-6013     |
Show/hide table
Effective Serial Numbers     |
S/N:C9N1275-UP     |
S/N:D9N1-UP     |
Caterpillar Information System:
C175-16 Generator Set Engine Engine Oil Pump - Disassemble
C175-16 Generator Set Engine Engine Oil Pump - Remove and Install
C32 Marine Engines Bearing Clearance - Check
2012/10/04 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1067}
C175-16 Generator Set Engine Engine Oil Cooler - Assemble
C175-16 Generator Set Engine Engine Oil Cooler - Disassemble
Coolant Line Upgrade for the Exhaust System Components on G3516B Engine.{1050, 1059, 1061, 1380} Coolant Line Upgrade for the Exhaust System Components on G3516B Engine.{1050, 1059, 1061, 1380}
C13, C15, and C18 Tier 4 Final Engines DEF Return Valve - Test
2012/10/23 A New Clamp is Now Used for the Air Lines Group on Certain Off-Highway Trucks and Quarry Trucks {1071, 1071}
C175-16 Generator Set Engine Engine Oil Cooler - Remove and Install
Procedure for Pre-Commissioning the IGBT on Certain UPSB505 Uninterruptible Power Supplies{1418, 4480} Procedure for Pre-Commissioning the IGBT on Certain UPSB505 Uninterruptible Power Supplies{1418, 4480}
C175-16 Generator Set Engine Auxiliary Water Pump - Assemble
2012/11/09 A New Canadian Standards Association (CSA) Ignition Harness Is Used by Certain G3406 Engines {1408}
C175-16 Generator Set Engine Engine Oil Pump - Assemble
C175-16 Generator Set Engine Engine Oil Filter Housing - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Remove and Install
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
C32 Marine Engines Heat Exchanger - Remove and Install
G3520E Generator Set Engines Cylinder Block
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}