A New Canadian Standards Association (CSA) Ignition Harness Is Used by Certain G3406 Engines {1408}
- Engine:
- G3406 (S/N: 4FD1-UP; 1RK1-UP)
Description of Change: The new harness has the following improvements:
- The design incorporates better sealing materials
- The new rail is a single piece of stainless steel tube with welded end caps
- The rail has riveted bosses which enable easy fastening of the braided wiring and help prevent moisture entry
- Better electrical seals are inside the rail
- A higher grade of moisture-resistant insulating foam completely fills the inside of the rail
- Interior and exterior surfaces are smoother in order to help prevent damage to wiring
Adaptable To:
Show/hide table
Illustration 1 | g03275237 |
396-2240 Power Harness As (IGNITION) |
The new 396-2240 Power Harness As (IGNITION) replaces the former 291-5862 Power Harness As (IGNITION), which is canceled.
The new harness is adaptable to the above engines equipped with the former 291-5862 Power Harness As .
The new harness is effective with the following serial numbers:
- 4FD04490
- 1RK00125
Caterpillar Information System:
2012/10/04 A New Unit Injector Wiring Group Is Used on Certain C9.3 Industrial Engines {1290, 1408, 1900}
C175-16 Generator Set Engine Engine Oil Pump - Disassemble
C175-16 Generator Set Engine Engine Oil Pump - Remove and Install
C32 Marine Engines Bearing Clearance - Check
2012/10/04 New Exhaust Shields and Seals Are Available for Certain On-Highway Truck Engines {1067}
C175-16 Generator Set Engine Engine Oil Cooler - Assemble
C175-16 Generator Set Engine Engine Oil Cooler - Disassemble
Coolant Line Upgrade for the Exhaust System Components on G3516B Engine.{1050, 1059, 1061, 1380} Coolant Line Upgrade for the Exhaust System Components on G3516B Engine.{1050, 1059, 1061, 1380}
C13, C15, and C18 Tier 4 Final Engines DEF Return Valve - Test
2012/10/23 A New Clamp is Now Used for the Air Lines Group on Certain Off-Highway Trucks and Quarry Trucks {1071, 1071}
C175-16 Generator Set Engine Engine Oil Cooler - Remove and Install
Procedure for Pre-Commissioning the IGBT on Certain UPSB505 Uninterruptible Power Supplies{1418, 4480} Procedure for Pre-Commissioning the IGBT on Certain UPSB505 Uninterruptible Power Supplies{1418, 4480}
C175-16 Generator Set Engine Engine Oil Pump - Assemble
C175-16 Generator Set Engine Engine Oil Filter Housing - Remove and Install
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Remove and Install
2012/10/22 A New Coolant Pressure Sensor Is Used on C175-16 Petroleum Engines {1439, 1439, 191W}
C175-16 Generator Set Engine Engine Oil and Water Pump Drive - Disassemble
C32 Marine Engines Heat Exchanger - Remove and Install
G3520E Generator Set Engines Cylinder Block
C1.5 and C2.2 Industrial Engines Customer Specified Parameters Table
2012/10/24 New Exhaust Valves Are Used in G3500 and G3500B Engines {1105}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}
2012/10/08 Set Engine Valve Lash After Installing All Remanufactured Long Blocks {1102, 1121, 1123, 1209}