Shipping the Machine
Show/hide table
当发动机转速自动控制(AEC)开关位于接通位置,操作操纵杆和/或行驶踏板时,发动机转速自动控制(AEC)机构会自动提高发动机转速。 当机器装上、卸下运输车时或在狭窄地段作业时,要将AEC开关置于“断开”(OFF)位置以防机器突然移动而导致严重伤亡事故。 机器上车前要将行驶速度控制开关置于“低速”(LOW)位置。 向拖车上装载机器时决不允许操作这个开关。 |
调查行驶道路上的限高。 确保为机器留出充足的空间。
在将机器装载到运输机器上之前,要清除装载货台及运输车斗板上的冰、雪或其它滑溜物质。 清除冰、雪或其它滑溜物质可防止机器在运输过程中滑动。
注: 遵守对装载货物特性(高度、重量、宽度和长度)的所有规定, 遵守所有管理宽货物的法规。
装卸机器时要选择最平坦的地面来进行。
- 装载机器之前要垫住拖车车轮或有轨车车轮。
- 当使用装卸斜坡时,要确保装卸斜坡有足够的长度、宽度、强度和坡度。
- 保持装卸斜坡与地面间坡度在15°以内。
- 将机器停放在可直接开上装卸斜坡的位置。 终传动应朝向机器的后面。 机器在装卸斜坡上时不得操作操纵杆。
注: 必须用两辆拖车装运超高的拆除配置。 前动臂和动臂尖端可以与斗杆和连杆机构一起运输。 机器和动臂底部将用单独的拖车装运。
- 机器经过装卸斜坡的接合处时要保持机器的平衡。
- 为防止机器滚动和突然移动,应进行下列工作:
- 垫住两条履带。
- 在几个位置处安装足够的系紧绳。
- 系好钢丝绳缆索。
- 垫住两条履带。
注: 请参阅操作和保养手册, "技术规格"。
Caterpillar Information System:
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Lifting and Tying Down the Machine
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Filter (Pilot) - Replace
G3500B Engines Detonation Sensor
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Drive Oil - Change
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Bearing - Lubricate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Indicators and Gauges - Test
2011/12/22 An Improvement to the Electronic Control Module is Made on Certain Excavators {1931, 7600}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Level - Check
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Filter (Case Drain) - Replace
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Piston Motor (Water Pump) Speed - Test
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Relief Valve (Cold Start) - Test
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Relief Valve (Charge, Water Delivery) - Test
C11 and C13 Engines Exhaust Manifold
2014/01/27 Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
C32 Marine Engine Refill Capacities
2011/11/11 Changes Have Been Made to the Fuel System Diagnostic Service Tests for C9.3 Industrial Engines {1250}
1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679} 1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679}
2011/11/29 New Software Is Now Used on Certain C15 Generator Sets {1901, 1920}
3516C Generator Set Engines Electronic Control Module (ECM)
C175-16 and C175-20 Generator Set Engines Engine Cranks but Does Not Start
C175-16 and C175-20 Generator Set Engines Exhaust Has Excessive White Smoke
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Drive Oil Sample - Obtain
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Gear - Lubricate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Counterweight Removal and Installation