Lifting and Tying Down the Machine
首选方法
撑杆
Show/hide table
不正确的起吊和系紧会导致负载移动,造成人身伤害或机器损坏. 在所提供的提升和系紧点上只能使用正确额定的钢绳和吊具。 按照操作和保养手册, "提升和系紧机器"中的正确工艺固定机器。 参阅操作和保养手册, "技术规格"中有关重量的资料。 |
Show/hide table
图 1 | g02161694 |
这种起吊方法是适用于所有机器的首选方法。 对于配重上带有螺纹衬套 (1) 的机器,这种方法是唯一可以接受的方法。
注: 螺纹衬套必须只能用于拆卸配重。 这些衬套无法支撑机器的重量。
注: 所列出的机器运输重量是机器最常用配置的标准重量。 如果机器上配有附件,机器的重量及机器的重心会有所改变。
请参阅操作和维护保养手册, "技术规格"中有关具体重量的资料。
- 吊装时使用正确规格的钢索和吊具。 将起重机放置到能够水平起吊机器的位置。
- 起吊钢索应有足够的长度以免刮碰机器。
- 撑杆的宽度和强度应足够大,以免碰触机器。
当钢索起吊时,钢索应滑到履带前支重轮和后支重轮处。
- 移动液压锁定操纵装置手柄至锁定位置。
注: 不得使用踏板作为起吊机器的起吊点。
其他方法(如有配备)
后起吊环和前起吊环
Show/hide table
不正确的起吊和系紧会导致负载移动,造成人身伤害或机器损坏. 在所提供的提升和系紧点上只能使用正确额定的钢绳和吊具。 按照操作和保养手册, "提升和系紧机器"中的正确工艺固定机器。 参阅操作和保养手册, "技术规格"中有关重量的资料。 |
Show/hide table
图 2 | g02161689 |
该起吊方法仅能作为备用方法用于起吊环 (1) 配备在配重上的机器。
注: 所列出的机器运输重量是机器最常用配置的标准重量。 如果机器上配有附件,机器的重量及机器的重心会有所改变。
参阅操作和保养手册, "技术规格"中具体的重量资料。
- 起吊时使用正确额定值的钢索和吊具。 将起重机放置到能够水平起吊机器的位置。
- 起吊钢索应有足够的长度以免刮碰机器。
- 使用下机架上的后起吊环和前起吊环来系紧绳索。 在尖角处使用尖角保护器。
- 把液压锁定操纵装置移到锁定位置。
Caterpillar Information System:
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Filter (Pilot) - Replace
G3500B Engines Detonation Sensor
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Drive Oil - Change
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Bearing - Lubricate
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Indicators and Gauges - Test
2011/12/22 An Improvement to the Electronic Control Module is Made on Certain Excavators {1931, 7600}
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Level - Check
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Hydraulic System Oil Filter (Case Drain) - Replace
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Piston Motor (Water Pump) Speed - Test
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Relief Valve (Cold Start) - Test
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Relief Valve (Charge, Water Delivery) - Test
CAT WDS OEM and 777F Off-Highway Truck/Tractor Water Delivery System Piston Pump (Steering) Pressure - Test and Adjust
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Shipping the Machine
C11 and C13 Engines Exhaust Manifold
2014/01/27 Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
C32 Marine Engine Refill Capacities
2011/11/11 Changes Have Been Made to the Fuel System Diagnostic Service Tests for C9.3 Industrial Engines {1250}
1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679} 1U-9600 Welding Group (U.S. and Canada) 1U-9601 Welding Group (All other countries){0599, 0679}
2011/11/29 New Software Is Now Used on Certain C15 Generator Sets {1901, 1920}
3516C Generator Set Engines Electronic Control Module (ECM)
C175-16 and C175-20 Generator Set Engines Engine Cranks but Does Not Start
C175-16 and C175-20 Generator Set Engines Exhaust Has Excessive White Smoke
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Drive Oil Sample - Obtain
345D MHPU and 349D MHPU Mobile Hydraulic Power Units Swing Gear - Lubricate