Camshaft
Show/hide table
| |
| 图 1 | g02582277 |
|
典型示例 | |
Show/hide table
| 技术规格 - 163-1419 凸轮轴总成 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| A | - | - | 新凸轮轴上止推垫圈组件的槽尺寸为 |
| C | 2 | 4N-1650 定位销 | 凸轮轴间定位销的延伸长度为 |
| D | 2 | 5B-5821 定位销 | 定位销从凸轮轴组件延伸的长度为 |
| E | 2 | 7N-3218 止推垫圈 | 新止推垫圈的厚度为 |
| F | - | - | 轴承轴颈的直径为 安装后凸轮轴轴承的孔径为 |
| - | - | - | 新凸轮轴组件的端隙为 |
| 1 | 16 | 5P-0076 螺栓 | 拧紧至扭矩为 |
Show/hide table
| |
| 图 2 | g02582338 |
Show/hide table
| 技术规格 - 163-1419 凸轮轴总成 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| - | - | - | 使用以下步骤确定实际凸轮轴凸轮升程：
1. 测量凸轮轴凸轮高度 (H)。 2. 测量基圆 (J)。 3. 从凸轮轴凸轮高度值 (H) 中减去基圆 (J)。 二者之差就是实际凸轮轴凸角升程。 |
| G | - | - | 规定的凸轮轴凸轮升程
进气凸轮为 喷油器凸轮为 排气凸轮为 |
Caterpillar Information System:
C9.3 Engine for Caterpillar Built Machines Water Pump
Cat® Alarm and Protection System Control Panel Overview (RP 410)
C9 Industrial Engines Aftercooler Core - Inspect/Clean/Test
C9 Industrial Engines Configuration Parameters
DPF Temperature Sensor Thread Salvage Procedure for Certain C7 thru C15 On-Highway Engines{108F, 1439, 1919, 7400} DPF Temperature Sensor Thread Salvage Procedure for Certain C7 thru C15 On-Highway Engines{108F, 1439, 1919, 7400}
2012/01/16 Special Instruction, REHS7131 , "Procedure for the Installation of the 372-1187 Nitrogen Oxide Sensor Gp and the 379-0138 Sensor Kit (NITROGEN OXIDE)" Is Available {1408, 1439, 191N, 7400}
2011/07/18 New Pressure Switch Is Now Used For Air Conditioner Refrigerant On Certain Cat Products {1435, 1809}
2011/05/12 New Software Is Now Released for Product Link PL522/523 Systems On All Cat Product {7606}
C3.4B Engines for Caterpillar Built Machines Piston Height - Inspect
C3.4B Engines for Caterpillar Built Machines Fuel System - Prime
C3.4B Engines for Caterpillar Built Machines V-Belt - Test
C3.4B Engines for Caterpillar Built Machines Flywheel Housing - Inspect
C15 Petroleum Engines Turbocharger
Procedure for the Installation of the 372-1187 Nitrogen Oxide Sensor Gp and the 379-0138 Sensor Kit (NITROGEN OXIDE){191N} Procedure for the Installation of the 372-1187 Nitrogen Oxide Sensor Gp and the 379-0138 Sensor Kit (NITROGEN OXIDE){191N}
797F and 797F XQ Off-Highway Truck Braking System Control Valve (Brake) - If Equipped
3500 Engines Camshaft
C13, C15, and C18 Tier 4 Final Engines Cylinder Block
3406C Industrial Engine Air Compressor - Check
UPSB220 Uninterruptible Power Supply Basic Preventive Maintenance
C9 Industrial Engines Belts - Inspect/Adjust/Replace
UPSB220 Uninterruptible Power Supply Unit Initial Check
UPSB220 Uninterruptible Power Supply Metering - Check
UPSB220 Uninterruptible Power Supply System Shutdown
UPSB220 Uninterruptible Power Supply Configuration - Check