1979/08/20 Caterpillar


Flex Plate Kits Are Now Available For Vickers Vane-Type Hydraulic Pumps{5055}

Usage:


Vickers Vane-Type Hydraulic Pumps With 20VQ, 25VQ, 35VQ and 45VQ Cartridges

SUPPLEMENT: 12/24/79

SERVICE MAGAZINE, AUGUST 20, 1979, PAGE 1. In the article "Flex Plate Kits Are Now Available For Vickers Vane-Type Hydraulic Pumps" that starts on Page 1 of the above Service Magazine, some wrong part numbers are shown in Chart B on Page 2. Correct these numbers as follows: For Pump Group 9J5041, change the Front Cartridge part number from 3G2247 to: 3G2747.

For Pump Group 9J5056, change the Front Cartridge part number from 3G1297 to: 3G2197.

For Pump Group 9J5061, change the Front Cartridge part number from 3G1298 to: 3G2198.

For Pump Group 9J5075, change the Rear Cartridge part number from 3G2932 to: 3G2832.

--------------- END SUPPLEMENT ---------------

Description of Change: Flex plate kits are now available for parts service of Vickers vane-type hydraulic pumps with "VQ" type cartridges. The flex plates are made of bronze with a steel back, and fit between the pump rotor and the support plates in VQ type pumps. Each kit has two flex plates and the necessary seals.

Tests show that the efficiency of a worn pump can be improved by the installation of new flex plates, if other components of the pump are still in good condition. Before a flex plate kit is installed, carefully inspect the condition of the pump. See the "Guideline For Reusable Parts" Form SEBF8025, and "Diagnosing Hydraulic Pump Failures" Form SEBD0501. The recommendation is to use these kits only in pumps that have a low number of hours, but the level of pump efficiency is no longer acceptable. Do not install the kit in a pump that has had a failure of other parts.

Adaptable To: All Vickers vane-type hydraulic pumps with 20VQ, 25VQ, 35VQ and 45VQ cartridges, including earlier pumps that have had a "VQ" type cartridge installed in place of the original "VHO" type cartridge. One kit is needed for each pump cartridge.

Chart A shows the kit part number for each cartridge size. Chart B shows the kit and cartridge part numbers in relation to pump groups. Chart C shows the kit part numbers in relation to cartridge part numbers. This chart can be used as a reference for earlier pumps that have a replacement "VQ" type cartridge installed.

Caterpillar Information System:

1979/08/13 Sealant Now Used On Pipe Plugs At The Bottom Of The Oil Filter Base Assembly To Prevent Oil Leakage{1306}
1979/08/13 New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13 New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13 6V14 Hydraulic Cylinder Group Now Available{0621}
1979/08/13 5P936 Liner Seat Insert Available For 6.25 Bore Engine Blocks With Counterbores{1217}
1979/08/13 New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet{1251,1253,1286}
1979/08/13 Splash Shields Added To Caterpillar Fuel Injection Test Bench{0652}
1979/08/06 Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06 Front Accessory Drive Group Changed; New Drive Parts For Fuel Transfer Pump{1256,1206}
1979/08/06 When Timing The Engine, Be Sure The Timing Bolt Is Installed In The Correct Hole In The Flywheel{1156,1251,1281}
1979/08/06 Use Correct Installation Procedure For Clutch Pilot Bearing In Rear Power Takeoff{3055}
1979/08/06 New Tools Are Available For Gasket Removal And Surface Reconditioning{0670}
1979/08/20 Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20 New Rear Cover And Gasket Used On Water Pump{1361,1350}
1979/08/27 Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27 New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27 Exhaust Manifold And Air Lines Groups Changed To Prevent Exhaust Leakage{1059,1061}
1979/08/27 Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27 6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}
1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}
1979/08/27 New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}
1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}
1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.