6V14 Hydraulic Cylinder Group Now Available{0621}
Usage:
- SUPPLEMENT: 09/03/79
SERVICE MAGAZINE, SEBD1927--AUGUST 13, 1979, PAGE 6, "6V14 Hydraulic Cylinder Group Now Available." The illustration has a wrong part number. Change 6V14 Cap to 6V15 Cap.
--------------- END SUPPLEMENT ---------------
The 6V14 Hydraulic Cylinder Group has been released as a puller for general use. This new hydraulic cylinder group has a capacity of 100 tons (890 kN). It has a center hole that permits use of the 5P7273 Stud with puller adapters.
Specifications for the 6V14 Hydraulic Cylinder Group are:
- Capacity: 100.1 Ton (890 kN) at 10,000 psi (69000 kPa)
- Effective Area: 20.02 in2 (129.16 cm2)
- Ram Travel: 6.0" (152.4 mm)
- Rod Diameter: 4.375" (111.12 mm)
- Cylinder Diameter: 7.25" (184.15 mm)
- Height: 11.688" (296.88 mm)
- Center Hole Diameter: 2.063" (52.39 mm)
- Weight: 92 lb (42 kg)
- Effective Area: 20.02 in2 (129.16 cm2)
The chart shows service parts available for this new service tool.
6V14 Hydraulic Cylinder Group.
Caterpillar Information System:
1979/08/13 5P936 Liner Seat Insert Available For 6.25 Bore Engine Blocks With Counterbores{1217}
1979/08/13 New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet{1251,1253,1286}
1979/08/13 Splash Shields Added To Caterpillar Fuel Injection Test Bench{0652}
1979/08/06 Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06 Front Accessory Drive Group Changed; New Drive Parts For Fuel Transfer Pump{1256,1206}
1979/08/06 When Timing The Engine, Be Sure The Timing Bolt Is Installed In The Correct Hole In The Flywheel{1156,1251,1281}
1979/08/06 Use Correct Installation Procedure For Clutch Pilot Bearing In Rear Power Takeoff{3055}
1979/08/06 New Tools Are Available For Gasket Removal And Surface Reconditioning{0670}
1979/07/09 New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower{1216}
1979/07/09 New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump{1264,1288}
1979/07/09 New Valve Cover Gasket Has Better Material{1107}
1979/07/09 Caution Label Added To 5P4150 Nozzle Testing Group{0651}
1979/08/13 New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13 New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13 Sealant Now Used On Pipe Plugs At The Bottom Of The Oil Filter Base Assembly To Prevent Oil Leakage{1306}
1979/08/20 Flex Plate Kits Are Now Available For Vickers Vane-Type Hydraulic Pumps{5055}
1979/08/20 Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20 New Rear Cover And Gasket Used On Water Pump{1361,1350}
1979/08/27 Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27 New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27 Exhaust Manifold And Air Lines Groups Changed To Prevent Exhaust Leakage{1059,1061}
1979/08/27 Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27 6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}
1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}