6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}
Usage:
All Sleeve Metering Fuel Systems
The 6V190 Clamp is now available for use on sleeve metering fuel systems. It is a direct replacement for the former 5P6562 Spring which is canceled. The new clamp holds the sleeve control shaft against the bearings to check or adjust the sleeve levers. The new clamp is held by a bolt to the cover of the fuel injection pump housing. It was possible for the former spring to become free.
The new 6V190 Clamp in use.
Caterpillar Information System:
1979/08/27 Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27 Exhaust Manifold And Air Lines Groups Changed To Prevent Exhaust Leakage{1059,1061}
1979/08/27 New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27 Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/20 New Rear Cover And Gasket Used On Water Pump{1361,1350}
1979/08/20 Turbocharger Bearings Are Now Available In More Different Sizes For Better Turbocharger Reconditioning{1053}
1979/08/20 Flex Plate Kits Are Now Available For Vickers Vane-Type Hydraulic Pumps{5055}
1979/08/13 Sealant Now Used On Pipe Plugs At The Bottom Of The Oil Filter Base Assembly To Prevent Oil Leakage{1306}
1979/08/13 New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13 New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13 6V14 Hydraulic Cylinder Group Now Available{0621}
1979/08/13 5P936 Liner Seat Insert Available For 6.25 Bore Engine Blocks With Counterbores{1217}
1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}
1979/08/27 New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}
1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}
1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}
1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}
1979/09/03 Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03 Different Mounting Hole Locations In Ring Gear Plate Assembly And Rotor Assembly For BrakeSaver{1155}
1979/09/10 Insulation Sleeve For 5P7360 Tach Generator Now Available {7462}
1979/09/10 Stronger Bolt Now Used With Exhaust Manifold {1059,1307}
1979/09/10 6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}
1979/09/10 Undercarriage Disassembly And Assembly Procedures And Specification Charts Are Available {4150,4159,4154,4171,4180}
1979/09/10 New Gasket Used In Water Lines Group For Aftercooler {1380,1063}