1979/09/10 Caterpillar

Insulation Sleeve For 5P7360 Tach Generator Now Available {7462}

Usage:

Short lengths of plastic tube are available for use as insulation sleeves around the plug connection for the 5P7360 Tach Generator. With no insulation sleeve in position during engine testing, the plug connection can short out against the vehicle assembly and possibly damage the 5P3600 Hydraulic Flow Meter.

To install the insulation sleeve, slide it over the plug connection as shown in the illustration and heat slowly with a cigarette lighter. The plastic sleeve will now fit evenly around the plug connection.

Order one insulation sleeve for each 5P7360 Tach Generator from:

Flo Tech, Inc.
403 South Washington Blvd.
Mundelein, IL 60060

5P7360 Tach Generator showing installation of insulation sleeve.

Ask for "shrinkable tubing for 5P7360 Tach Generator." Include a self-addressed stamped envelope with your order.

Caterpillar Information System:

1979/09/03 Different Mounting Hole Locations In Ring Gear Plate Assembly And Rotor Assembly For BrakeSaver{1155}

1979/09/03 Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}

1979/09/03 Follow Recommendations Given In Special Instructions For Modification Of Rollover Protective Structures (ROPS) At All Times{7323,7325}

1979/09/03 Only One Dowel Pin Is Now Used To Hold The Thrust Bearing In The Correct Position{1053,1052}

1979/08/27 New Design Thrust Plate Used In Crankshaft Group{1201,1202,1203}

1979/08/27 New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}

1979/08/27 Engine Oil Viscosity Changed To SAE 10W/30 For Shipment From All U. S. Factories{1318}

1979/08/27 6V190 Clamp Is Available For Use On Sleeve Metering Fuel Systems{0626,1250}

1979/08/27 Service Kit Is Available For Woodward UG8 Governor{1289}

1979/08/27 Exhaust Manifold And Air Lines Groups Changed To Prevent Exhaust Leakage{1059,1061}

1979/08/27 New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}

1979/08/27 Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}

1979/09/10 Stronger Bolt Now Used With Exhaust Manifold {1059,1307}

1979/09/10 6V2055 High Vacuum Grease Gives Better Oil Seal {1052,1053,1077,0682}

1979/09/10 Undercarriage Disassembly And Assembly Procedures And Specification Charts Are Available {4150,4159,4154,4171,4180}

1979/09/10 New Gasket Used In Water Lines Group For Aftercooler {1380,1063}

1979/09/10 Different Grease Fitting Now Used In Fan Drive Group {1359}

1979/09/10 Recommendation For Use Of A FLEX-HONE On 1100, 3100 and 3200 Series Engines {1201}

1979/09/10 Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement

1979/09/10 Pin Bore Is Now Offset (Not In The Center) .059" (1.5 mm) In The Piston To Stop Vibration Of The Cylinder Liners Which Can Cause Pitting On The Coolant Side Of The Cylinder Liners {1214,1216}

1979/09/10 Engines Can Use Crankshafts With Either Six Or Eight Counterweights {1202}

1979/09/17 New Main And Connecting Rod Bearings Have A Thicker Layer Of Surface Material{1230,1203,1219}

1979/09/17 New BrakeSaver Control Valve Group Has Improved Diaphragm{1159,1155}

1979/09/17 Keystone Piston Groups Can Be Installed In Earlier Engines In Steiger Tractors{1214,1215}