Engine Oil Bypass Valve - Remove and Install
Removal Procedure
Start By:
- Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove" for the correct procedure.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove two bolts (1) that fasten the engine oil relief valve to the engine oil pump.
Show/hide table
Illustration 1 | g00552240 |
- Remove bolt (3) that holds engine oil relief valve (4) in position.
- Remove engine oil relief valve (4) and the gasket from the engine.
- Disconnect oil tube (2) and remove the O-ring seals from the oil tube.
Installation Procedure
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install new O-ring seals on oil tube (2) and connect oil tube (2) to the engine oil pump.
Show/hide table
Illustration 2 | g00552240 |
- Place the new gasket in position and install engine oil relief valve (4) on the engine.
- Install bolt (3) that holds engine oil relief valve (4) in position. Tighten bolt (3) to a torque of 44 N·m (33 lb ft).
- Install two bolts (1) that fasten the engine oil relief valve to the engine oil pump.
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Install" for the correct procedure.
Caterpillar Information System:
3054B Industrial Engine Rocker Shaft and Pushrod - Remove
2009/04/13 Parts For Caterpillar Switch Gear Are Now Available {4491}
2009/04/06 New Information Is Available For Intelligent Switchgear Organization (ISO) Products {4491}
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Disassemble
Guidelines for Inspection of the 303-8189 Flexible Coupling Gp {3252, 4450} Guidelines for Inspection of the 303-8189 Flexible Coupling Gp {3252, 4450}
C13 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 1273 - FMI 14
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 1273 - FMI 09
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 1273 - FMI 02
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0811 - FMI 09
2009/04/27 New Software for C15 Generator Sets Is Available {1901, 1920}
3054B Industrial Engine Rocker Shaft and Pushrod - Install
C18 Marine Engines Overhaul (Top End)
C7.1 Industrial Engine Safety Messages
Replacement of the Fuel Manifold (Rail){1251, 1290} Replacement of the Fuel Manifold (Rail){1251, 1290}
C7.1 Industrial Engine General Hazard Information
C9.3 Tier 4 Interim Engines Fuel Rail Pressure Is Low
CX31-P600 Petroleum Transmission Transmission Warm-up
CX31-P600 Petroleum Transmission Transmission Control
CX31-P600 Petroleum Transmission Retarder Operation
CX31-P600 Petroleum Transmission Transmission Cooling System
C7.1 Industrial Engine Burn Prevention
CX31-P600 Petroleum Transmission Lubricant Viscosities