MID 053 - CID 1273 - FMI 14
产生此代码的情况:
Show/hide table
图 1 | g02729055 |
数据链路示意图 |
当底盘 ECM 不以正确的速率向 Advisor ECM 发送必要的参数时,记录此诊断代码。 底盘 ECM 生成参数的更新率不正确。 由于底盘 ECM 没有响应 Advisor ECM 请求的参数,导致通信故障。 这种情况不是由断开的线束或故障导线导致。 断开的线束或故障导线将导致出现一个 FMI-9。
产生此诊断代码的可能原因如下:
- 底盘 ECM 安装了不正确的软件。
- Advisor ECM 安装了不正确的软件。
- 可能安装了不兼容的软件。
- 底盘 ECM 的保险丝可能有故障。
测试步骤 1. 检查底盘 ECM 和 Advisor ECM 的软件版本是否正确。
- 利用 Caterpillar 电子技师(ET)验证软件版本是否兼容。
预期结果:
Advisor ECM 和底盘 ECM 上安装了正确版本的软件。
结果:
- 是 - 软件版本兼容。 转至测试步骤 2。
- 否 - 未安装正确的软件。
修复: 闪存相应 ECM 的合适软件。 循环钥匙开关以初始化新软件。 确保诊断代码不再为激活状态。
停止
测试步骤 2. 重新检查是否有诊断代码。
- 确保该诊断代码处于激活状态。
预期结果:
诊断代码处于非激活状态。 诊断代码指示灯处于非激活状态。
结果:
- 是 - 诊断代码指示灯和诊断代码都处于非激活状态。
修复: 清除诊断代码。
停止
- 否 - 诊断代码处于激活状态。
修复: 请在更换 ECM 之前确保安装了正确的软件。 如果软件正确,应更换 Advisor ECM。 参见测试和调整, "电子控制模块(ECM)- 更换 "。 如果刚更换了 Advisor ECM,则安装新的底盘 ECM。 请参阅所维修机器的测试和调整, "电子控制模块(ECM)- 更换"。
停止
Caterpillar Information System:
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 1273 - FMI 09
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 1273 - FMI 02
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0811 - FMI 09
2009/04/27 New Software for C15 Generator Sets Is Available {1901, 1920}
C13 Engines for Caterpillar Built Machines Exhaust Sensor Lines - Remove and Install - Venturi
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0590 - FMI 14
2009/04/13 New Software Is Available for C18 Marine Engines {1901, 1920}
Update to the Wiring Harness and the Electrical System on Some C-15 Engines for Hazardous Locations{1000, 1408, 1901} Update to the Wiring Harness and the Electrical System on Some C-15 Engines for Hazardous Locations{1000, 1408, 1901}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0590 - FMI 09
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0590 - FMI 02
2009/04/13 New Application Loader Software For Caterpillar Switch Gear Is Now Available {4491, 7620}
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0296 - FMI 09
C13 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
Guidelines for Inspection of the 303-8189 Flexible Coupling Gp {3252, 4450} Guidelines for Inspection of the 303-8189 Flexible Coupling Gp {3252, 4450}
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Disassemble
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Assemble
2009/04/06 New Information Is Available For Intelligent Switchgear Organization (ISO) Products {4491}
2009/04/13 Parts For Caterpillar Switch Gear Are Now Available {4491}
3054B Industrial Engine Rocker Shaft and Pushrod - Remove
3054B Industrial Engine Engine Oil Bypass Valve - Remove and Install
3054B Industrial Engine Rocker Shaft and Pushrod - Install
C18 Marine Engines Overhaul (Top End)
C7.1 Industrial Engine Safety Messages
Replacement of the Fuel Manifold (Rail){1251, 1290} Replacement of the Fuel Manifold (Rail){1251, 1290}