Engine Overspeeds
使用本步骤诊断和排除发动机超速故障,或在以下事件代码为激活状态时使用本步骤。 关于事件代码的信息,请参阅故障诊断与排除, "事件代码"。 有关发动机监控系统的信息,请参阅故障诊断与排除, "发动机监控系统"。
注: 以下某些代码可能不适用于特定的应用。
Show/hide table
故障诊断代码     | |||
---|---|---|---|
CDL 代码     | J1939 代码     | 代码说明 (代码说明可能不同)     |
注释     |
E362(1)     | 190-15     | 发动机超速     | 记录该代码。     |
E362(3)     | 190-0     | 发动机超速     | 此代码需要出厂密码才能清除。     |
可能原因
- 继续沿陡坡下行(如果适用)
- 涡轮增压器的正常工作
- 进气
- 起动辅助装置工作异常
建议的措施
注: 下面以概率的先后顺序列出了这些步骤。 依次完成这些步骤。
Show/hide table
故障诊断与排除测试步骤     | 数值     | 结果     |
---|---|---|
1. 继续沿陡坡下行(如果适用) 可能需要在陡坡上接合发动机制动器。 A. 使用发动机制动器时,操作员需要了解正确的机器操作方法。 并非所有应用场合都有发动机制动器。     |
陡坡     |
结果:陡坡是超速的原因所在。 控制陡坡上的发动机转速。 结果:陡坡不是超速的原因所在。 转至测试步骤 2。     |
2. 涡轮增压器的正常工作 A. 检查涡轮增压器是否正常工作。 B. 检查是否有任何机油漏入进气口中。     |
涡轮增压器     |
结果:涡轮增压器中的机油漏入进气口中。 修理或更换涡轮增压器。 结果:涡轮增压器中的机油没有漏入进气口中。 转至测试步骤 3。     |
3. 进气 A. 检查周围有无可燃气体。 B. 检查起动辅助装置(如果配备)是否正常工作。     |
空气质量     |
结果:大气中含有可燃气体。 不要在有可燃气体的环境中运行发动机。     |
按所列步骤顺序完成以上步骤。
以上步骤解决了此问题。 将发动机重新投入使用。
以上步骤没有解决问题。
联系当地 Cat 代理商的技术通信员(TC)。 如需进一步的帮助,您的 TC 可以通过代理商解决方案网络(DSN)与您交谈。
Caterpillar Information System:
C13 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C9.3 Engines for Caterpillar Built Machines Symptom Troubleshooting
C7.1 Industrial Engine and Generator Set ECM Memory - Test
C15 and C18 Engines for Caterpillar Built Machines Belt Tensioner - Remove and Install
C12 Marine Engines Engine and Marine Transmission Operation
789D, 793F, and 797F Off-Highway Truck Monitoring System MID 053 - CID 0271 - FMI 03
C13, C15, and C18 Tier 4 Interim Engines Power Is Intermittently Low or Power Cutout Is Intermittent
C15 and C18 Engines for Caterpillar Built Machines Crankshaft Position Sensor - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Cooling Fan Is Always ON
C6.6 Industrial Engine Starter Motor
C6.6 Industrial Engine Engine Oil Pressure
C9.3 Engines for Caterpillar Built Machines Valve Lash Is Excessive
2009/04/13 Procedure to Install the Muffler Bracket on Weatherproof Generator Set Enclosures and Improved Sealing of the Enclosures {0649, 1062}
2009/04/06 A New Paint Scheme Is Used on C7 through C32 Marine Engines with the Pleasurecraft Finish {1000, 7559, 7581}
Installation and Maintenance of the Microfilter for Natural Gas {1261} Installation and Maintenance of the Microfilter for Natural Gas {1261}
C13 Engine for Caterpillar Built Machines Vibration Damper and Pulley - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Crankcase Pressure Is High
C13 Engine for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C13, C15, and C18 Tier 4 Interim Engines Engine Stalls at Low RPM
C13 Engines for Caterpillar Built Machines Flywheel - Remove and Install
C9.3 Engines for Caterpillar Built Machines Engine Top Speed Is Not Obtained
C13 Engine for Caterpillar Built Machines Alternator - Remove and Install
Quick Start Guide for Manual Paralleling{7451} Quick Start Guide for Manual Paralleling{7451}
C7.1 Industrial Engine Model View Illustrations