Fabricated Adapters Permit Horizontal Mounting Of Transmissions On 1P2420 Transmission Repair Stand{0640}
Usage:
Adapters can be fabricated and installed on the 1P2420 Transmission Repair Stand to make it more usable (Illustration 1). With the FT1392 Adapters, the serviceman can put a 7-speed or 8-speed transmission in a horizontal position on the repair stand (Illustration 2). In this position, disassembly and assembly of the transmission especially the transfer gears and hydraulic control, is easier. Use the chart that follows and Illustration 3 to fabricate the FT1392 Adapters.
Illustration 1. Adapters installed on repair stand.
Illustration 2. Transmission installed on stand in horizontal position.
Illustration 3. Instructions to fabricate FT1392 Adapters.
Caterpillar Information System:
1978/02/27 New Seal Assembly With Longer Ferrule Prevents Damage To Ferrule During Cylinder Head Installation{1100,1101,1300}
1978/02/13 Complete Set Of Contact Points For Dial Indicators Is Now Available In One Group{0653}
1978/02/13 Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool{1361,0622}
1978/02/06 Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06 New Water Temperature Regulator Opens At 180°F (82°C){1350,1355,7304}
1978/02/06 Attachment Groups Put Corrosion Inhibitor Directly Into Cooling System{1350}
1978/02/06 Successful Engine Service-3208 Engine Booklet Is Available{1000}
1978/02/06 Smaller Quantity Of Oil Now Used In Engine Oil Pan; Prevents Contact Between Crankshaft And Oil{1318}
1978/01/30 Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30 Stronger Front Support Assembly{1153}
1978/01/30 New Water Pump Cover Has A Baffle And Wall To Send Coolant Flow From Bypass Line Directly Into Water Pump{1361}
1978/01/30 Oil Strainer (Screen) Added To Turbocharger Thrust Bearing{1052,1053}
1978/02/27 Replacement Seals And Wear Sleeves Now Available As A Crankshaft Seal Kit{1202,1160,1161}
1978/02/27 Stronger Exhaust Manifold Gasket Now Used{1059}
1978/02/27 Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob{1258}
1978/02/27 Modification Of Oil Pan For Installation Of Oil Sump Heater{1302}
1978/02/27 New Tachometer Drive Adapter Assembly Prevents Failure Of The Seals For the Tachometer Drive Group And Transfer Pump{7462,1256}
1978/03/06 Stronger Piston And Connecting Rod Are Tapered In Area Of Piston Pin{1213,1214,1218}
1978/03/06 5P8558 Pressure Gauge Calibrating Group Checks Pressure Gauges{0650}
1978/03/06 Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06 New Starter Motors Have Solenoid On Top Of Starter{1407,1453}
1978/03/13 5P8687 Tee Test Tooling Group{0651,5050}
1978/03/13 When A 6N5906 Hour Meter Will Not Operate Correctly, Check The Electrical Supply Before A Replacement Hour Meter Is Installed{7480,1400}
1978/03/13 Soft Washers And Lockwashers Are Now Used With The Mounting Bolts For Air-Fuel Ratio Control{1278,1264}