Accessory Drive - Assemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
B | 7M-7456 | 轴承安装固定胶 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查齿轮 (7) 的轮齿和花键是否磨损或损坏。 拆下轴承 (6) 和轴承 (8)。 检查簧环 (9) 和前壳体 (4) 是否磨损或损坏。 更换任何损坏或磨损的部件。
- 在轴承 (6) 的内表面 (X) 处连续涂敷一小滴工具 (B)。 将齿轮轴放在适当的支架上。 按压轴承 (6) 的内表面直至轴承 (6) 抵到齿轮 (7) 的凸肩上。 清除所有多余的密封胶。
- 在轴承 (8) 的内表面 (Z) 处连续涂敷一小滴工具 (B)。 将轴承 (8) 内表面放在适当的支架上。 将齿轮 (7) 的轴按压至轴承 (8) 中直至齿轮的凸肩抵到轴承上。 清除所有多余的密封胶。
- 在轴承 (6) 和 (8) 的外表面 (Y) 处连续涂敷一小滴工具 (B)。 将附件驱动壳体 (4) 放在适当的支架上。 将齿轮组件按入附件驱动壳体中。 确保轴承 (6) 抵到附件驱动壳体 (4) 中的凹槽前面。 清除所有多余的密封胶。
- 将簧环 (9) 安装到附件驱动壳体 (4) 的槽中。 确保簧环 (9) 在槽中的位置正确。
Show/hide table
图 1 | g01440577 |
典型实例 |
Caterpillar Information System:
C4.4 Industrial Engine Accessory Drive - Disassemble
C4.4 Industrial Engine Accessory Drive - Remove
345D, 349D and 349D2 Excavators Hydraulic System Travel on Level Ground - Test - Optional Test
C11 and C13 Petroleum Engines Accessory Drive - Install
345D, 349D and 349D2 Excavators Hydraulic System Engine Performance - Test - Engine Speed
C11 and C13 Petroleum Engines Accessory Drive - Remove
Installation Instructions for the New Caterpillar Digital Voltage Regulator (CDVR) In Field Retrofit Applications{4467} Installation Instructions for the New Caterpillar Digital Voltage Regulator (CDVR) In Field Retrofit Applications{4467}
Software Update for Model Year 2007 C7 On-Highway Engine in General Motor Chassis{1901} Software Update for Model Year 2007 C7 On-Highway Engine in General Motor Chassis{1901}
C11 and C13 Petroleum Engines Flywheel Housing - Remove and Install
2008/03/24 New Check Valves are Now Used on the Oscillating Axle on Excavators {5468}
C11 and C13 Petroleum Engines Crankshaft Rear Seal - Install
C11 and C13 Petroleum Engines Crankshaft Rear Seal - Remove
C4.4 Industrial Engine Accessory Drive - Install
Procedure for Cleaning Ash from the Diesel Particulate Filter (DPF) for Certain Caterpillar Engines{108F, 1091} Procedure for Cleaning Ash from the Diesel Particulate Filter (DPF) for Certain Caterpillar Engines{108F, 1091}
Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091} Procedure to Handle and Ship Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM){1091, 1091}
C9 Marine Auxiliary and Generator Set Engines Configuration Parameters
G3500B Engines Water Temperature Regulator
C13T-TH35 and C15T-TH35 Petroleum Packages Plate Locations and Film Locations
2008/02/11 The Wiring Harness for the Turbocharger Compressor Outlet Pressure Sensor has been Rerouted {1403, 1408, 1917}
345D, 349D and 349D2 Excavators Hydraulic System Travel on Level Ground - Test
345D, 349D and 349D2 Excavators Hydraulic System Swing Speed and Swing Drift on a Slope - Check
C11 and C13 Engines for Caterpillar Built Machines Valve Mechanism Cover - Remove and Install
C15 On-Highway Engine Diesel Particulate Filter - Disassemble
345D, 349D and 349D2 Excavators Hydraulic System Cylinder Speed - Check