Engine Monitoring System
电子控制模块(ECM)监控发动机的运转参数。 如果特定发动机参数超过发动机监控系统所定义的可接受范围,则 ECM 将产生事件代码。 有关事件代码的信息,请参阅故障诊断和排除, "事件代码",了解针对此应用的相应事件代码列表。
四个客户可编程设定级别可用来监控特定的发动机参数。 客户可编程设定的等级取决于应用软件。 以下级别可用于:
- 断开
- 警告(默认设定)
- 减额
- 停机
ECM 可能允许将特定的事件代码编程设定为不同的级别。 请参阅表 1。
Show/hide table
94-1 燃油压力低警告     | |
100-1 机油压力低警告     | |
100-11 机油压力极低     | |
105-0 进气歧管温度高警告     | |
105-11 进气歧管温度极高     | |
110-0 冷却液温度高警告     | |
110-11 冷却液温度极高     | |
111-1 冷却液液位低警告     | |
111-11 冷却液液位极低     |
某些参数具有三种可能的响应。 有些响应对某些参数是无效的。 请参阅表 2。
Show/hide table
指示灯 (1)、(2) 和 (3)     | |
---|---|
警告类别指示位     | 严重程度     |
(1)     | "最低严重程度"     |
(2)     | "中等严重程度"     |
(3)     | "最高严重程度"     |
使用 Caterpillar 电子技师(ET)执行下列系统监控活动:
- 查看参数。
- 参数编程
- 响应配置
- 设置延迟时间
参数的默认设置是在出厂时编程设置的。 为了适应特定的用途和场所,可以使用 Cat ET 对某些参数重新编程。 Cat ET 屏幕为触发点的改变提供了指导。
注: 有些参数不需要密码即可进行更改。 有些参数的更改需要用户密码。 有些参数受工厂密码的保护。 有些参数无法进行更改。
查看或更改监控系统的设置
使用以下程序来查看参数设置和/或更改参数设置:
- 在 Cat ET 上选择 "Service/Monitoring System"(维修 / 监控系统)屏幕。
- 高亮显示所需参数。 接着点击屏幕左下角的 "Change(更改)"按钮。
会出现 "Change Monitor System"(更改监控系统)屏幕。
- 更改参数的"状态"。
- 按照屏幕下半部分显示的 "Allowed Values(容许值)"设置 "Trip Point(触发点)"和 "Delay Time(延迟时间)"。
- 点击 "OK"(确认)按钮。
如果需要密码,会出现 "Enter Passwords"(输入密码)屏幕。 输入正确的密码,然后点击 "OK"(确定)按钮。
注: 如果需要工厂密码,会出现 "Enter Factory Passwords"(输入工厂密码)屏幕。 有关获得出厂密码的信息,请参阅故障诊断和排除, "出厂密码"。
新的设置会立即生效。
Caterpillar Information System:
C32 Marine Generator Set Engine Oil and Filter - Change
3176C, 3406E and 3456 Industrial Engines Indicator Lamps
3608 Engine Camshaft Bearings - Install
3608 Engine Prelubrication Oil Pump - Install
3608 Engine Prelubrication Oil Pump - Remove
3608 Engine Fuel Pressure Control Valve - Install
3608 Engine Fuel Pressure Control Valve - Assemble
3608 Engine Water Pump Seal - Install
3608 Engine Water Pump Seal - Remove
3608 Engine Auxiliary Water Pump - Assemble
2008/11/01 New Lines and Clamps are Now Used for the Air Control Group {1087, 7554}
3608 Engine Water Pump - Install
3176C, 3406E and 3456 Industrial Engines Electronic Display Module
C32 Marine Engine Fuel System Secondary Filter - Replace
3176C, 3406E and 3456 Industrial Engines Configuration Parameters
Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490} Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}
C27 and C32 Industrial and Petroleum Engines Exhaust Manifold
3608 Engine Prelubrication Oil Pump - Assemble
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3608 Engine Fuel Transfer Pump - Disassemble
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
C-15, C-16, and C-18 Truck Engines Belt Tensioner
C15 and C18 Petroleum Generator Sets Model View Illustrations
C18 Petroleum Generator Sets Model View Illustrations