Camshaft Bearings - Install
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 8T-0970     | Camshaft Bearing Tool     | 1     |
B     | 6V-7047     | Single Acting Cylinder     | 1     |
C     | 8T-3035     | Tensioner Lines Gp     | 1     |
8T-0820 | Hydraulic Pressure Gauge     | 1     | |
3S-6224 | Electric Hydraulic Pump Gp     | 1     | |
8S-8033 | Electric Hydraulic Pump Gp     | 1     | |
9U-6600 | Hand Hydraulic Pump     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put Tooling (A) and Tooling (B) in position for installation, and put camshaft bearing (1) in position for installation. Put camshaft bearing (1) in position with the joint at the top. Apply clean engine oil to the outside of the camshaft bearing. Tooling (A) is piloted into the bearing bores or into the cylinder block bores.
Note: Refer to Disassembly and Assembly, "General Information (Reference Material)" for more information.
Show/hide table
Illustration 1 | g00576120 |
Show/hide table
Illustration 2 | g00576362 |
- Connect Tooling (C) to Tooling (B) .
- Move the camshaft bearing into position in the cylinder block. Camshaft bearing (1) is properly located when the groove that is around the outside is in the middle of the plugged hole. Refer to Specifications, "Camshaft Bearings" for the correct dimensions in order to install the camshaft bearings.
- Before you install the rear camshaft bearing, align the hole in the camshaft bearing. This placement will allow camshaft timing pin (2) to be put into position in the camshaft.
Show/hide table
Illustration 3 | g00576363 |
- Press the rear camshaft bearing into position.
End By: Install the camshaft segments. Refer to Disassembly and Assembly, "Camshaft - Install".
Caterpillar Information System:
3608 Engine Prelubrication Oil Pump - Install
3608 Engine Prelubrication Oil Pump - Remove
3608 Engine Fuel Pressure Control Valve - Install
3608 Engine Fuel Pressure Control Valve - Assemble
3608 Engine Water Pump Seal - Install
3608 Engine Water Pump Seal - Remove
3608 Engine Auxiliary Water Pump - Assemble
2008/11/01 New Lines and Clamps are Now Used for the Air Control Group {1087, 7554}
3608 Engine Water Pump - Install
3608 Engine Water Pump - Remove
3608 Engine Cylinder Liner - Install
3176C, 3406E and 3456 Industrial Engines Component Location
3176C, 3406E and 3456 Industrial Engines Indicator Lamps
C32 Marine Generator Set Engine Oil and Filter - Change
3176C, 3406E and 3456 Industrial Engines Engine Monitoring System
3176C, 3406E and 3456 Industrial Engines Electronic Display Module
C32 Marine Engine Fuel System Secondary Filter - Replace
3176C, 3406E and 3456 Industrial Engines Configuration Parameters
Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490} Generation 3 DPFdm Diagnostic Module Installation Manual - California Only {1000, 1091, 7490}
C27 and C32 Industrial and Petroleum Engines Exhaust Manifold
3608 Engine Prelubrication Oil Pump - Assemble
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley
3608 Engine Fuel Transfer Pump - Disassemble
C27 and C32 Industrial and Petroleum Engines Vibration Damper and Pulley