Cylinder Head
Show/hide table
图 1 | g01647473 |
按照以下步骤拧紧缸盖螺栓:
注: 组装前,将清洁的发动机机油涂抹到螺栓的螺纹上。
- 用手将螺栓 1 到螺栓 6 拧紧至最大扭矩 15 N·m (11 lb ft)。
- 按数字次序拧紧螺栓 1 到螺栓 6 至 100 ± 10 N·m (75 ± 7 lb ft)。
- 再次按数字次序拧紧螺栓 1 到螺栓 6 至 250 ± 15 N·m (185 ± 11 lb ft)。
- 再次按数字顺序将螺栓 1 到螺栓 6 转动 180 ± 5 度。
(1) 将清洁的发动机机油涂抹在 O 形密封圈的孔径上。
注: 组装前,先将 4C-5599 防粘结剂 涂抹在喷油器套筒的螺纹上。
(2) 喷油器套筒的安装扭矩 ... 120 ± 10 N·m (90 ± 7 lb ft)
Show/hide table
图 2 | g01561694 |
(K) 新缸盖的高度 ... 208 mm (8.2 in)
注: 安装杯塞前,用 6V-6640 密封胶 润滑杯塞的孔径。
(E) 5 个杯塞自缸盖表面的安装深度 ... 1.00 ± 0.25 mm (0.039 ± 0.010 in)
Show/hide table
图 3 | g01647474 |
(E) 15 个杯塞自缸盖表面的安装深度 ... 0.75 ± 0.25 mm (0.030 ± 0.010 in)
Caterpillar Information System:
3608 Engine Turbocharger - Install
3608 Engine Turbocharger - Assemble
3608 Engine Turbocharger - Disassemble
3608 Engine Turbocharger - Remove
Procedure to Update a Standard TH48-E80 Oil/Gas Transmission to a Warm-Up Mode TH48-E80 Oil/Gas Transmission{1408, 3083, 3160, 3168, 4800, 7610} Procedure to Update a Standard TH48-E80 Oil/Gas Transmission to a Warm-Up Mode TH48-E80 Oil/Gas Transmission{1408, 3083, 3160, 3168, 4800, 7610}
3608 Engine Exhaust Manifold - Remove and Install
C15 and C18 Petrolem Generator Set Engines Sensor Signal (Analog, Passive) - Test
3608 Engine Air Inlet Shutoff - Remove and Install
3608 Engine Fuel Transfer Pump - Install
3608 Engine Fuel Priming Pump - Assemble
3608 Engine Fuel Priming Pump - Disassemble
C15 and C18 Petrolem Generator Set Engines Sensor Signal (Analog, Active) - Test
14L Motor Grader Machine Systems Circle - Remove
3176C and 3196 Engines for Caterpillar Built Machines Engine Support (Front)
2007/12/24 An Improved Exhaust Bellow is Used {1059}
3608 Engine Prelubrication Oil Pump - Disassemble
3608 Engine Prelube Valve (Continuous) - Remove and Install
3608 Engine Priority Valve - Assemble
3608 Engine Priority Valve - Install
3608 Engine Engine Oil Filler and Oil Level Gauge - Remove and Install
14L Motor Grader Machine Systems Circle - Install
C12 Marine Engines Belts - Inspect/Adjust/Replace
3608 Engine Valve Cover Base - Remove and Install
3516C Generator Set Engine System Overview