Electrical Connectors
Connectors for the Electronic Control Module (ECM)
Show/hide table
| |
| Illustration 1 | g06123997 |
|
Locations of the components on the engine ECM (1) P2 ECM connector (harness side) (2) P2 ECM connector (ECM side) (3) Engine ECM (4) P1 ECM connector (ECM side) (5) P1 ECM connector (harness side) | |
Show/hide table
| |
| Illustration 2 | g06124000 |
|
Numbering arrangement of ECM connector pins | |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 151-6320 | Removal Tool (Red) | 1 |
Show/hide table
| |
| Illustration 3 | g01877813 |
|
Removal Tool | |
- Remove the connector from the ECM. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install".
- Position Tooling (A) around wire (2).
Note: Make sure that the tool stays perpendicular to the face of connector (1).
- Push the tool into the hole for the terminal. Gently pull the wire to remove the terminal from the rear of connector (1).
- Remove the Tooling (A) from the wire.
Note: If a terminal must be replaced, part number 9X-3402 must be used for 16 and 18 AWG wire. Part number 126-1768 must be used for 14 AWG wire.
- Push the terminal into the rear of connector (1) until the terminal engages with the locking device.
- Gently pull on wire (2) to make sure that the terminal is retained by the locking device.
- Connect the connector to the ECM and then tighten the retaining screw to a torque of
6 N·m (53 lb in) .
Show/hide table
| |
| Illustration 4 | g03745086 |
Analog Sensor Connector (active)
Show/hide table
| |
| Illustration 5 | g01240891 |
Analog Sensor Connector (passive)
Show/hide table
| |
| Illustration 6 | g01241538 |
Connectors for the Termination Resistor
Show/hide table
| |
| Illustration 7 | g01355248 |
Show/hide table
| |
| Illustration 8 | g01155187 |
Show/hide table
| |
| Illustration 9 | g02219254 |
Show/hide table
| |
| Illustration 10 | g02220494 |
Caterpillar Information System:
C7.1 Engines and Generator Sets Diagnostic Capabilities
C7.1 Engines and Generator Sets Diesel Particulate Filter Regeneration
C4.4 (Mech) Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Type 2 Exhaust Manifold
910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Water Temperature Regulator - Remove and Install
910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Valve Mechanism Cover - Remove and Install
980L Medium Wheel Loaders Event Codes
980L Medium Wheel Loaders Diagnostic Trouble Codes
980L Medium Wheel Loaders Diagnostic Capabilities
High-Speed Transfer Drive Retaining Ring Failure on Certain Compact Wheel Loaders {3159, 4350, 4355} High-Speed Transfer Drive Retaining Ring Failure on Certain Compact Wheel Loaders {3159, 4350, 4355}
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
C7.1 Engines and Generator Sets Component Location
C7.1 Engines and Generator Sets System Overview
C7.1 Engines and Generator Sets Configuration Parameters
C7.1 Engines and Generator Sets Diagnostic Trouble Codes
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Disassemble
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Assemble
992K Wheel Loader Systems Piston Pump (Steering)
992K Wheel Loader Systems Hydraulic Tank (Steering, Brake)
New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258} New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258}
980L Medium Wheel Loaders Steering System
D6N Track-Type Tractor Monitoring System Operator Menu
980L Medium Wheel Loaders Torque Converter Lockup Clutch Does Not Engage
980L Tier 3 Wheel Loader Machine System Bucket - Remove and Install
980L Medium Wheel Loaders Transmission Clutch Slips