Bucket - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 518-0684 | Sleeve | 1 |
350-7768 | Electric Hydraulic Pump Gp | 1 | |
6V-3175 | Double Acting Cylinder | 1 | |
4C-9634 | Puller Stud | 1 | |
7H-7539 | Nut | 1 | |
4K-0684 | Hard Washer | 1 | |
B | 452-6006 | Grease | - |
C | 518-0684 | Sleeve | 1 |
350-7768 | Electric Hydraulic Pump Gp | 1 | |
6V-3175 | Double Acting Cylinder | 1 | |
137-8460 | Puller Stud | 1 | |
9U-5346 | Nut | 1 |
Start By:
- Connect the steering frame lock.
- Position the bucket flat on the ground.
- Release the hydraulic system pressure.
Show/hide table
Illustration 1 g06124459 - Attach a suitable lifting device to bucket tilt link (1). The weight of bucket tilt link (1) is approximately
60 kg (132 lb) . Remove bolt (2), the washer, and the spacer from pin assembly (3).Show/hide tableIllustration 2 g00391840 Typical example - Attach Tooling (A) to pin assembly (3). Use two people to remove pin assembly (3) and Tooling (A). The weight of pin assembly (3) and Tooling (A) is approximately
36 kg (80 lb) . Remove pin assembly (3). - Repeat Step 3 and Step 4 to remove the pin assembly from the opposite side of the bucket.
Show/hide table
Illustration 3 g06124502 - Position suitable cribbing under lift arms (4).
- Remove bolt (6), the washers, and the spacer from pin assembly (5).
Show/hide table
Illustration 4 g06430691 - Attach Tooling (C) to pin assembly (5) (not shown). Use two people to remove pin assembly (5) and Tooling (A). The weight of pin assembly (5) and Tooling (C) is approximately
36 kg (80 lb) . Remove pin assembly (5). - Repeat Step 7 and Step 8 to remove the pin assembly from the opposite side of the bucket.
Show/hide table
Illustration 5 g03487577 - Attach suitable lifting device to bucket (7). The weight of bucket (7) is approximately
3700 kg (8157 lb) . Remove bucket (7).
- Install bucket (7) in the reverse order of the removal.
- Apply Tooling (B) to the bores of the pin assemblies before installation.
Caterpillar Information System:
980L Medium Wheel Loaders Torque Converter Lockup Clutch Does Not Engage
D6N Track-Type Tractor Monitoring System Operator Menu
980L Medium Wheel Loaders Steering System
New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258} New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258}
992K Wheel Loader Systems Hydraulic Tank (Steering, Brake)
992K Wheel Loader Systems Piston Pump (Steering)
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Assemble
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Disassemble
C7.1 Engines and Generator Sets Diagnostic Trouble Codes
C7.1 Engines and Generator Sets Configuration Parameters
C7.1 Engines and Generator Sets Electrical Connectors
C7.1 Engines and Generator Sets Diagnostic Capabilities
980L Medium Wheel Loaders Transmission Clutch Slips
D6K and D6K2 Track-Type Tractor Monitoring System Service Menu
3500E Marine Engines Overhaul Recommendations
Improved Retention Method For The Headliner Of Certain PL61 Pipelayers {7301} Improved Retention Method For The Headliner Of Certain PL61 Pipelayers {7301}
Installation Procedure for the TLV2 Seat Suspension Harness {1408, 7324} Installation Procedure for the TLV2 Seat Suspension Harness {1408, 7324}
Ordering NOx Reduction System Coolers for C9.3, C13, C15, and C18 Engines {108G} Ordering NOx Reduction System Coolers for C9.3, C13, C15, and C18 Engines {108G}
953K Track-Type Loader Machine Systems Calibration Error Codes
953K Track-Type Loader Machine Systems Calibration
953K Track-Type Loader Machine Systems Operational Checks
953K Track-Type Loader Machine Systems Hydraulic Pump - Test and Adjust
953K Track-Type Loader Machine Systems Accumulator (Pilot) - Test and Charge
854K Wheel Dozer Systems Gear Pump (Implement)