910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Caterpillar


Water Temperature Regulator - Remove and Install

Usage:

910M H22

Removal Procedure


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Dispose of all fluids according to local regulations and mandates.


  1. Drain the coolant from the cooling system to a level below the water temperature regulator, into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct draining procedure.

  2. Loosen the hose clamps from the upper radiator hose and disconnect the upper radiator hose from water temperature regulator housing (2).


    Illustration 1g01343959
    Typical example

  3. Remove bolts (1) from water temperature regulator housing (2).

  4. Remove water temperature regulator housing (2) from the cylinder head.

    Note: Note the orientation of the water temperature regulator housing.



    Illustration 2g01343959
    Typical example

  5. Remove O-ring seal (3) from water temperature regulator housing (2).

Installation Procedure

Table 1
Required Tools 
Tool  Part Number  Part Description  Qty 
A  1U-6396  O-Ring Assembly Compound 


NOTICE

Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.


  1. Ensure that all components of water temperature regulator are clean and free of wear or damage. Check the water temperature regulator for correct operation. Refer to Systems Operation, Testing and Adjusting, "Water Temperature Regulator - Test" for the procedure to test the water temperature regulator. If any components of the water temperature regulator are worn or damaged, the complete assembly must be replaced.


    Illustration 3g01343960
    Typical example

  2. If the original water temperature regulator housing is installed, position a new O-ring seal (3) into the groove in water temperature regulator housing (2).

    A new water temperature regulator housing is supplied with a new O-ring seal.

  3. Use Tooling (A) to lubricate the new O-ring seal.

  4. Install water temperature regulator housing (2) to the cylinder head.

    Note: Ensure the correct orientation of the water temperature regulator housing.



    Illustration 4g01343959
    Typical example

  5. Install bolts (1). Tighten the bolts to a torque of 22 N·m (16 lb ft).

  6. Connect the upper radiator hose and tighten the hose clamps.

  7. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.

Caterpillar Information System:

910M, 914M, 918M, 910K, and 914K Compact Wheel Loaders, Engine Supplement Valve Mechanism Cover - Remove and Install
980L Medium Wheel Loaders Event Codes
980L Medium Wheel Loaders Diagnostic Trouble Codes
980L Medium Wheel Loaders Diagnostic Capabilities
High-Speed Transfer Drive Retaining Ring Failure on Certain Compact Wheel Loaders {3159, 4350, 4355} High-Speed Transfer Drive Retaining Ring Failure on Certain Compact Wheel Loaders {3159, 4350, 4355}
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
C7.1 Engines and Generator Sets Component Location
C7.1 Engines and Generator Sets System Overview
C7.1 Engines and Generator Sets Welding Precaution
994K Wheel Loader Machine Systems Lift Position Control - Remove and Install
C7.1 Engines and Generator Sets General Information
DEF Injector Troubleshooting on Certain C4.4 Engines {108I} DEF Injector Troubleshooting on Certain C4.4 Engines {108I}
C4.4 (Mech) Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install - Type 2 Exhaust Manifold
C7.1 Engines and Generator Sets Diesel Particulate Filter Regeneration
C7.1 Engines and Generator Sets Diagnostic Capabilities
C7.1 Engines and Generator Sets Electrical Connectors
C7.1 Engines and Generator Sets Configuration Parameters
C7.1 Engines and Generator Sets Diagnostic Trouble Codes
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Disassemble
980L Tier 3 Wheel Loader Engine Supplement Fuel Priming Pump - Assemble
992K Wheel Loader Systems Piston Pump (Steering)
992K Wheel Loader Systems Hydraulic Tank (Steering, Brake)
New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258} New Pinion Bevel Gear Set Is Now Used on the 950 GC Medium Wheel Loader {3254, 3256, 3258}
980L Medium Wheel Loaders Steering System
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.