Alternator - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Disconnect harness assemblies (2), (3), and (4) from alternator (5).
- Loosen adjusting nuts (1) in order to provide slack for the belt.
Show/hide table
Illustration 2 g00599024 - Remove nuts and washers (6) in order to remove belt guard (7).
- Remove belt (8) from the pulley for the alternator.
- Remove bolt (9) in order to disconnect the alternator from the adjusting rod.
- Remove bolt (10) in order to disconnect the alternator from the support. Remove alternator (5).
Show/hide table
| |
| Illustration 1 | g00599021 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position alternator (5) on the support. Install bolts (9) and (10) in order to hold alternator (5) in place. Do not tighten the bolts at this time.
- Install belt (8) on the pulley for the alternator.
- Adjust the belt tension. Refer to Specifications, "Belt Tension Chart". In order to adjust the belt tension, turn adjusting nuts (1). Tighten adjusting nuts (1).
- After the belt tension has been adjusted, install belt guard (7). Secure the belt guard to bolts (9) and (10) with nuts and washers (6).
- Connect harness assemblies (2), (3), and (4).
Show/hide table
| |
| Illustration 3 | g00599024 |
Show/hide table
|
| |
| Illustration 4 | g00599021 |
Caterpillar Information System:
3512C Industrial Engine Cylinder Head - Remove
C15 and C18 Generator Set Engines Fuel Cooler - Remove and Install
G3500 A3 Engines Engine Coolant Temperature (High)
2007/06/25 New Pressure Sensors are Used {1000, 1408, 1900}
Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119} Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119}
3512C Industrial Engine Flywheel - Remove and Install
C4.4 (Mech) Industrial Engine Engine Valve Lash - Inspect/Adjust
C18 Industrial Engines Aftercooler Core - Clean/Test - Air-To-Air Aftercooler (If Equipped)
C9 Engine Safety Messages
Fluid Power and Electrical Graphic Symbols Electrical Power Graphic Symbols
3176C, 3406E and 3456 Industrial Engines Electronic Service Tools
3512C Industrial Engine Crankshaft - Install
3512C Industrial Engine Accessory Drive (Front) - Remove
Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030} Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030}
3512C Industrial Engine Flywheel Housing - Install
C15 and C18 Generator Set Engines Expansion Tank - Remove and Install
G3500 A3 Engines Turbocharger
G3500 A3 Engines Exhaust Manifold - Water cooled
G3508, G3512 and G3516 Engines Nitrogen Oxide Sensor - Remove and Install
2007/07/02 A New Spark Plug is Available {1550, 1555}
G3300 Engines Product Storage
C7 Petroleum Engine Speed Sensor - Clean/Inspect
DE Series Generator Set with Cat C1.1, C1.5, and C2.2 Engines Cooling System Coolant Sample (Level 2) - Obtain
C15 Petroleum Engine Cooling System Supplemental Coolant Additive (SCA) - Test/Add