Flywheel - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
B | - | Guide Stud
1 - 14 NF by 8 inch |
2 |
C | 2D-1201 | Eyebolts | 2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove the magnetic pickups.
Show/hide table
Illustration 1 g00911678 - Install Tooling (A) on flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately
167 kg (370 lb) . - Remove two bolts (2) from the crankshaft.
- Install Tooling (B).
- Remove remaining bolts (2).
- Remove flywheel (1).
Use the following procedure if flywheel (1) is not easily separated from the crankshaft:
- Install Tooling (C) in each side of flywheel (1).
- Use a prybar to remove flywheel (1) from the crankshaft.
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 138-7573 | Link Bracket | 2 |
B | - | Guide Stud
1 - 14 NF by 8 inch |
2 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the condition of the flywheel ring gear. Use the following procedure in order to replace the ring gear, if necessary.
- Remove the damaged ring gear from the flywheel.
- Raise the temperature of the new ring gear.
- Install the gear on the flywheel. Ensure that the chamfer of the gear teeth will be toward the pinion of the starting motor.
Show/hide tableIllustration 2 g00911678 - Install Tooling (B) in the end of the crankshaft.
- Install Tooling (A) onto flywheel (1) and attach a suitable lifting device. The weight of flywheel (1) is approximately
167 kg (370 lb) .Note: Ensure that the mark on flywheel (1) is aligned with the mark on the crankshaft.
- Lift flywheel (1) into position onto Tooling (B).
- Apply clean engine oil to bolts (2) and install bolts (2).
- Remove Tooling (A) and Tooling (B). Install remaining two bolts (2). Tighten bolts (2) to the correct torque.
Note: Refer to Specifications, "Flywheel" for the correct torque.
- Install the magnetic pickups.
Caterpillar Information System:
C4.4 (Mech) Industrial Engine Engine Valve Lash - Inspect/Adjust
C18 Industrial Engines Aftercooler Core - Clean/Test - Air-To-Air Aftercooler (If Equipped)
C9 Engine Safety Messages
Fluid Power and Electrical Graphic Symbols Electrical Power Graphic Symbols
3176C, 3406E and 3456 Industrial Engines Electronic Service Tools
3512C Industrial Engine Crankshaft - Install
3512C Industrial Engine Crankshaft - Remove
Air/Fuel Ratio Control Electrical Connections
3512C Industrial Engine Camshaft - Install
C32 Marine Propulsion Engines Synchronization - Test
C9.3 Industrial Engine and CX31-P600-C9I Petroleum Power Train Package Reference Material
2007/06/25 Do Not Allow the Advisor Display to Overheat {7490}
Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119} Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119}
2007/06/25 New Pressure Sensors are Used {1000, 1408, 1900}
G3500 A3 Engines Engine Coolant Temperature (High)
C15 and C18 Generator Set Engines Fuel Cooler - Remove and Install
3512C Industrial Engine Cylinder Head - Remove
3512C Industrial Engine Alternator - Remove and Install
3512C Industrial Engine Accessory Drive (Front) - Remove
Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030} Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030}
3512C Industrial Engine Flywheel Housing - Install
C15 and C18 Generator Set Engines Expansion Tank - Remove and Install
G3500 A3 Engines Turbocharger
G3500 A3 Engines Exhaust Manifold - Water cooled