Fuel Cooler - Remove and Install
拆卸步骤
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
 |
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害，当更换燃油滤清器或油水分离器滤芯时，要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
- 断开蓄电池。
- 将供油开关置于 OFF（接通）位置。
- 拆下螺栓 (1) 。 拆下护罩 (2) 。
Show/hide table
 | |
| 图 1 | g01390803 |
- 拆下软管组件 (3) 。
Show/hide table
 | |
| 图 2 | g01390806 |
- 拆下螺栓 (4) 。 拆下燃油冷却器 (5) 。
Show/hide table
 | |
| 图 3 | g01390808 |
安装步骤
- 放置燃油冷却器 (5) 入位，并安装螺栓 (4) 。
Show/hide table
| | |
| 图 4 | g01390808 |
- 安装软管组件 (3) 。
Show/hide table
| | |
| 图 5 | g01390806 |
- 安装护罩 (2) 并安装螺栓 (1) 。
Show/hide table
| | |
| 图 6 | g01390803 |
- 将供油开关置于 OFF（接通）位置。
- 连接蓄电池。
Caterpillar Information System:
G3500 A3 Engines Engine Coolant Temperature (High)
2007/06/25 New Pressure Sensors are Used {1000, 1408, 1900}
Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119} Missing Pipe Plugs on the C-10, C-12, C-15, C15, and C-16 Engines Jake Brake{1119}
3512C Industrial Engine Flywheel - Remove and Install
C4.4 (Mech) Industrial Engine Engine Valve Lash - Inspect/Adjust
C18 Industrial Engines Aftercooler Core - Clean/Test - Air-To-Air Aftercooler (If Equipped)
C9 Engine Safety Messages
Fluid Power and Electrical Graphic Symbols Electrical Power Graphic Symbols
3176C, 3406E and 3456 Industrial Engines Electronic Service Tools
3512C Industrial Engine Crankshaft - Install
3512C Industrial Engine Crankshaft - Remove
Air/Fuel Ratio Control Electrical Connections
3512C Industrial Engine Cylinder Head - Remove
3512C Industrial Engine Alternator - Remove and Install
3512C Industrial Engine Accessory Drive (Front) - Remove
Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030} Bench Test Procedure For A TH31-E61 Oil/Gas Transmission With A Drop Box {3030}
3512C Industrial Engine Flywheel Housing - Install
C15 and C18 Generator Set Engines Expansion Tank - Remove and Install
G3500 A3 Engines Turbocharger
G3500 A3 Engines Exhaust Manifold - Water cooled
G3508, G3512 and G3516 Engines Nitrogen Oxide Sensor - Remove and Install
2007/07/02 A New Spark Plug is Available {1550, 1555}
G3300 Engines Product Storage
C7 Petroleum Engine Speed Sensor - Clean/Inspect