Stick - 7.1 m (23.32 ft)
Show/hide table
| |
| Illustration 1 | g03820936 |
|
Right side view Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the bucket, and cylinder pin bores. | |||
| 1 | - | - | Assemble the stick cylinder so that the grease zerk is directed, as shown. |
| 2 | 2 | 166-1498 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 3 | 1 | 113-2963 Pin As | Diameter is |
| 4 | 1 | 4I-4811 Pin As | Diameter is |
| 5 | 2 | 235-7679 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 6 | 2 | 166-1494 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 7 | 2 | 228-5621 Bushing(1) | Bore before assembly is Installation depth is |
| 8 | 2 | Bushing(2) | Bore before assembly is Bore before assembly is Installation depth is |
| 9 | 2 | Bushing(2) | Bore before assembly is Bore before assembly is Installation depth is |
Show/hide table
| (1) | Install the bushings in the bore so that the part number of each bushing is facing outward. |
| (2) | For 229-1096 |
| (3) | For 563-4059 |
| (4) | For 240-2913 |
| (5) | For 563-4060 |
Caterpillar Information System:
Procedure to Install VIMS Application Module for Payload on all Underground Articulated Trucks {7610, 7620} Procedure to Install VIMS Application Module for Payload on all Underground Articulated Trucks {7610, 7620}
953K and 963K Track-Type Loaders Cab Filter (Recirculation) - Clean/Inspect/Replace
953K and 963K Track-Type Loaders Fuel System Filter (In-Line) - Replace
D8T Track-Type Tractor Location of Components (Power Train System)
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Display Menu
D6R2 Track-Type Tractor Machine Systems Piston Motor (Steering) - Remove and Install
2015/06/10 A New Special Instruction , "Procedure for Replacing the Actuator on Certain H Series Wheel Tractor-Scrapers Equipped with Powered Access Ladders" is Now Available {7254}
D3K2, D4K2 and D5K2 Track-Type Tractors Machine Systems Bulldozer C-Frame (VPAT) - Remove and Install
D6R2 Track-Type Tractor Machine Systems Refrigerant Accumulator - Remove and Install
953K and 963K Track-Type Loaders Condenser (Refrigerant) - Clean
2015/04/03 A Heavy Duty Push Arm Step is now Available for Certain D6T and D7E Track-Type Tractors {6061, 6063, 7256}
D6R2 Track-Type Tractor Machine Systems Blower Motor (Air Conditioner, Heater) - Remove and Install
336F and 340F Excavators Machine System Specifications Auxiliary Hydraulic Lines
336, 336 GC and 340 Excavator Systems Stick Lines
C2.2 Engines For Caterpillar Built Machines General Information
336, 336 GC and 340 Excavator Systems Boom - 10.6 m (34.99 ft)
C2.2 Engines For Caterpillar Built Machines Welding Precaution
994K Wheel Loader Machine Systems Electronic Control Module (ECM) - Flash Program
2015/04/07 An Improved Transmission Oil Level Check Procedure Is Used on Certain M-Series Medium Wheel Loaders {3030}
C2.2 Engines For Caterpillar Built Machines Electronic Service Tools
994K Wheel Loader Machine Systems Calibrations (Operator Monitor)
C2.2 Engines For Caterpillar Built Machines Service Information Report
C2.2 Engines For Caterpillar Built Machines System Overview
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Machine Menu