Boom - 10.6 m (34.99 ft)
Show/hide table
| |
| Illustration 1 | g06101347 |
|
Right side view Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, stick, upper frame, bushing, and cylinder pin bores. After you assemble the bushings coat all the bores and the bushings with 5P-0960 Grease Cartridge. | |||
| 1 | 2 | 166-1498 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 2 | 1 | 192-8321 Pin | Diameter is |
| 3 | 1 | 359-5743 Pin As | Diameter is |
| 4 | 1 | 113-2963 Pin As | Diameter is |
| 5 | 2 | Bushing | Install the bushing in the bore so that the part number of the bushing is facing outward.
Bore before assembly is Installation depth is |
| As required, use the following shims in order to adjust the maximum lateral clearance of Mount the steel shims in order to be located at the boom side. |
|||
| 6 | 1 | 147-3957 Shim | Thickness is |
| 7 | 2 | 093-0084 Shim | Thickness is |
| 1 | 093-0116 Shim | Thickness is |
|
| 1 | 113-2127 Shim | Thickness is |
|
Caterpillar Information System:
C2.2 Engines For Caterpillar Built Machines General Information
336, 336 GC and 340 Excavator Systems Stick Lines
336F and 340F Excavators Machine System Specifications Auxiliary Hydraulic Lines
336, 336 GC and 340 Excavator Systems Stick - 7.1 m (23.32 ft)
Procedure to Install VIMS Application Module for Payload on all Underground Articulated Trucks {7610, 7620} Procedure to Install VIMS Application Module for Payload on all Underground Articulated Trucks {7610, 7620}
953K and 963K Track-Type Loaders Cab Filter (Recirculation) - Clean/Inspect/Replace
953K and 963K Track-Type Loaders Fuel System Filter (In-Line) - Replace
D8T Track-Type Tractor Location of Components (Power Train System)
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Display Menu
D6R2 Track-Type Tractor Machine Systems Piston Motor (Steering) - Remove and Install
2015/06/10 A New Special Instruction , "Procedure for Replacing the Actuator on Certain H Series Wheel Tractor-Scrapers Equipped with Powered Access Ladders" is Now Available {7254}
D3K2, D4K2 and D5K2 Track-Type Tractors Machine Systems Bulldozer C-Frame (VPAT) - Remove and Install
C2.2 Engines For Caterpillar Built Machines Welding Precaution
994K Wheel Loader Machine Systems Electronic Control Module (ECM) - Flash Program
2015/04/07 An Improved Transmission Oil Level Check Procedure Is Used on Certain M-Series Medium Wheel Loaders {3030}
C2.2 Engines For Caterpillar Built Machines Electronic Service Tools
994K Wheel Loader Machine Systems Calibrations (Operator Monitor)
C2.2 Engines For Caterpillar Built Machines Service Information Report
C2.2 Engines For Caterpillar Built Machines System Overview
924K, 926M, 930K, 930M, 938K and 938M Wheel Loaders Information Display Machine Menu
994K Wheel Loader Machine Systems Calibrations, Diagnostic Tests (Cat ET)
C2.2 Engines For Caterpillar Built Machines Component Location
D6R2 Track-Type Tractor Machine Systems Piston Pump (Steering) - Remove and Install
994K Wheel Loader Machine Systems Position Sensor (Lift Linkage) - Replace