Tire and Rim - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 447-0910 | Electric Hydraulic Pump Gp 115v | 1 |
4C-5749 | Mobile Base Gp | 1 | |
8S-7620 | Base As | 2 | |
8S-7650 | Cylinder As | 2 | |
8S-7615 | Pin | 2 | |
8S-7645 | Hydraulic Jack Hose Gp | 2 | |
B | 283-4495 | Stand | 2 |
8S-7611 | Tube | 2 | |
8S-7615 | Pin | 2 | |
C | 447-0911 | Electric Hydraulic Pump Gp 230v | 1 |
4C-5749 | Mobile Base Gp | 1 | |
8S-7610 | Base As | 2 | |
8S-7650 | Cylinder As | 2 | |
8S-7615 | Pin | 2 | |
8S-7645 | Hydraulic Jack Hose Gp | 2 |
Start By:
- Connect the steering frame lock.
- Remove the cab removal group.
- Steps 2 through 6 are for the removal of the rear left tire and rim.
Show/hide table
Illustration 1 g03738425 - Remove bracket (1) and panel (2).
Show/hide table
Illustration 2 g03738322 - Remove fender cover (3) and fender (4). Use two people to remove fender (5). The weight of fender (5) is approximately
36 kg (80 lb) .Show/hide tableIllustration 3 g03738336 Show/hide tableIllustration 4 g02793520 - Use Tooling (A) in order to raise rear tires and rims (5) off the ground by several inches. Position Tooling (B) under the machine, as shown in Illustration 4. Use Tooling (A) in order to lower the machine onto Tooling (B). Remove Tooling (A).
Show/hide table
Illustration 5 g03738344 - Install suitable cribbing in order to keep oscillating axle (6) level.
Show/hide table
Illustration 6 g03738441 Typical Example - Attach a suitable lifting device to left rear tire and rim (5). The weight of left rear tire and rim (5) is approximately
340 kg (750 lb) . Remove the bolts and use the suitable lifting device in order to remove tire and rim (5). - Steps 8 through 11 are for the removal of the rear right tire and rim.
Show/hide table
Illustration 7 g03738448 - Remove fenders (7).
Show/hide table
Illustration 8 g03738336 Show/hide tableIllustration 9 g02793520 - Use Tooling (A) in order to raise rear tires and rims (5) off the ground by several inches. Position Tooling (B) under the machine, as shown in Illustration 9. Use Tooling (A) in order to lower the machine onto Tooling (B). Remove Tooling (A).
Show/hide table
Illustration 10 g03738344 - Install suitable cribbing in order to keep oscillating axle (6) level.
Show/hide table
Illustration 11 g03738460 - Attach a suitable lifting device to tire and rim (5). The weight of tire and rim (5) is approximately
340 kg (750 lb) . Remove the bolts and use the suitable lifting device in order to remove tire and rim (5). - Steps 13 through 15 are for the removal of the front tires and rims.
Show/hide table
Illustration 12 g03738462 Show/hide tableIllustration 13 g02793817 - Use Tooling (C) in order to raise tires and rims (7) off the ground by several inches . Position Tooling (B) under the machine, as shown in Illustration 13. Use Tooling (C) in order to lower the machine onto Tooling (B). Remove Tooling (C).
Show/hide table
Illustration 14 g03738466 - Remove fender (8).
Show/hide table
Illustration 15 g03738490 - Attach a suitable lifting device to tire and rim (7). The weight of tire and rim (7) is approximately
340 kg (750 lb) . Remove the bolts and use the suitable lifting device in order to remove tire and rim (7). - Repeat Steps 13 through 15 for the opposite side of the machine.
- Install tires and rims (5) and (7) in the reverse order of removal.
- Tighten tire and rim bolts to a torque of
300 ± 40 N·m (220 ± 30lb ft) turn an additional 60° ± 5°.
Caterpillar Information System:
2014/11/03 New Replacement Parts for the Torque Converter Are Now Used on Certain Large Wheel Loaders, Wheel Dozers, and Landfill Compactors {3101, 3105}
C27 and C32 Engines for Caterpillar Built Machines Data Link Configuration Status - Test
621K Wheel Tractor-Scraper Sound Information and Vibration Information
D7E Track-Type Tractor Systems Air Conditioner
C27 and C32 Engines for Caterpillar Built Machines Data Link - Test
Throttle Pedal Sensor Calibration{1269, 1913, 5736, 5737, 7610, 7620} Throttle Pedal Sensor Calibration{1269, 1913, 5736, 5737, 7610, 7620}
C27 and C32 Engines for Caterpillar Built Machines Cooling Fan Reversing - Test
D6R2 Track-Type Tractor Engine Supplement Air Cleaner - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Manifold - Remove and Install - Hydrostatic
926M, 930M and 938M Wheel Loaders Power Train Accumulator - Remove and Install - Hydrostatic
D6R2 Track-Type Tractor Engine Supplement Electric Starting Motor - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Gear Pump (Hydrostatic, Charge) - Assemble
D7E Track-Type Tractor Systems Air Conditioner
Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357} Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357}
D6R2 Track-Type Tractor Engine Supplement Engine Side Guards - Remove and Install
D6R2 Track-Type Tractor Engine Supplement Fan - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines NRS Exhaust Gas Temperature Is High
C27 and C32 Engines for Caterpillar Built Machines Intake Manifold Air Pressure Is Low
D7R Track-Type Bulldozer Cooling System Coolant Sample (Level 1) - Obtain
D7R Track-Type Bulldozer Engine Oil Sample - Obtain
926M, 930M and 938M Wheel Loaders Power Train Drive Shaft - Remove and Install
D7R Track-Type Bulldozer Winch Fairlead Rollers - Lubricate - If Equipped
D7R Track-Type Bulldozer Fuel Tank Water and Sediment - Drain
335F CR Excavator C7.1 Engine Supplement Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor