Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
- Disconnect harness assembly (1) from absolute pressure sensor (2).
- Remove absolute pressure sensor (2) from the sensor manifold.
- Disconnect harness assembly (5) from differential pressure sensor (4).
- Remove bolts (3) and differential pressure sensor (4) from the sensor manifold.
Show/hide table
Illustration 2 g03738700 - Remove O-ring seal (6) from absolute pressure sensor (2). Discard O-ring seal (6).
Show/hide table
Illustration 3 g03738701 - Remove O-ring seals (7) from differential pressure sensor (4). Discard O-ring seals (7).
Show/hide table
| |
| Illustration 1 | g03738697 |
Show/hide table
| NOTICE |
|---|
|
Ensure that wiring harness are correctly routed and the cable straps are not over tightened. Over tightening of the cable straps will damage the wiring harness convoluting. |
- Install absolute pressure sensor (2) and differential pressure sensor (4) in the reverse order of removal.
- Tighten bolts (3) to torque of
22 N·m (195 lb in) . - Tighten absolute sensor (2) to torque of
10 N·m (89 lb in) .
- Tighten bolts (3) to torque of
Caterpillar Information System:
D7R Track-Type Bulldozer Fuel Tank Water and Sediment - Drain
D7R Track-Type Bulldozer Winch Fairlead Rollers - Lubricate - If Equipped
926M, 930M and 938M Wheel Loaders Power Train Drive Shaft - Remove and Install
D7R Track-Type Bulldozer Engine Oil Sample - Obtain
D7R Track-Type Bulldozer Cooling System Coolant Sample (Level 1) - Obtain
C27 and C32 Engines for Caterpillar Built Machines Intake Manifold Air Pressure Is Low
C27 and C32 Engines for Caterpillar Built Machines NRS Exhaust Gas Temperature Is High
D6R2 Track-Type Tractor Engine Supplement Fan - Remove and Install
D6R2 Track-Type Tractor Engine Supplement Engine Side Guards - Remove and Install
Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357} Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357}
D7E Track-Type Tractor Systems Air Conditioner
926M, 930M and 938M Wheel Loaders Power Train Tire and Rim - Remove and Install
926M, 930M and 938M Wheel Loaders Power Train Fixed Axle (Front) - Remove and Install
2014/12/09 An Improved SystemOne Self Cleaning Track Shoe is Now Available for Certain D6N and D6M Track-Type Tractors {4170}
D6R2 Track-Type Tractor Engine Supplement Fan Drive - Remove and Install
D7R Track-Type Bulldozer Fuel System - Prime
2014/10/27 Improved Solenoid Valve Group Is Now Used On Certain Load Haul Dumps and Wheel Loaders {3073, 3139, 5479}
335F CR Excavator C7.1 Engine Supplement Turbocharger - Remove and Install
D7E Track-Type Tractor Systems Bank Valve (Two)
D7E Track-Type Tractor Systems Bank Valve (Two)
D7E Track-Type Tractor Systems Bulldozer Brace
D7E Track-Type Tractor Systems Bulldozer Trunnion
D7E Track-Type Tractor Systems Push Arm
D7E Track-Type Tractor Systems Control Valve (Bulldozer Lift)