Drive Shaft - Remove and Install
Start By:
- Connect the steering frame lock.
- Remove bolts (2) and the strap that fasten front drive shaft (3) to fixed axle (1). Discard bolts (2).
Show/hide table
Illustration 2 g03738579 - Disconnect hose assembly (4).
- Remove bolts (6).
- Remove bolts (5) and the strap that fasten front drive shaft (3) to center drive shaft (7). Discard bolts (5).
- Remove front drive shaft (3) from the machine.
Show/hide table
| |
| Illustration 1 | g03738573 |
- Install front drive shaft (3) in the reverse order of removal.
- Install new bolts (5) and tighten until snug. Tighten bolts (5) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern. - Install new bolts (2) and tighten until snug. Tighten bolts (2) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern.
- Install new bolts (5) and tighten until snug. Tighten bolts (5) to a torque of
Start By:
- Connect the steering frame lock.
- Remove bolts (1) and the strap that fasten center drive shaft (2) to transmission yoke (3). Discard bolts (2).
Show/hide table
Illustration 4 g02836821 - Remove bolts (4) and the strap that fasten center drive shaft (2) to front drive shaft (5). Discard bolts (4).
- Remove center drive shaft (2) from the machine.
Show/hide table
| |
| Illustration 3 | g02836818 |
- Install center drive shaft (2) in the reverse order of removal.
- Install new bolts (4) and tighten until snug. Tighten bolts (4) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern. - Install new bolts (1) and tighten until snug. Tighten bolts (1) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern.
Note: Install center drive shaft (2) with the female end toward the transmission.
- Install new bolts (4) and tighten until snug. Tighten bolts (4) to a torque of
Start By:
- Connect the steering frame lock.
- Remove bolts (2) and the strap that fasten rear drive shaft (3) to yoke (1). Discard bolts (2).
- Remove bolts (4) and the strap that fasten rear drive shaft (3) to yoke (5). Discard bolts (4).
- Remove rear drive shaft (3) from the machine.
Show/hide table
| |
| Illustration 5 | g03738622 |
- Install rear drive shaft (3) in the reverse order of removal.
Note: Install rear drive shaft (3) with the female end toward the transmission.
- Install new bolts (4) and tighten until snug. Tighten bolts (4) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern. - Install new bolts (2) and tighten until snug. Tighten bolts (2) to a torque of
71 ± 10 N·m (52 ± 7 lb ft) using an X pattern.
- Install new bolts (4) and tighten until snug. Tighten bolts (4) to a torque of
Caterpillar Information System:
D7R Track-Type Bulldozer Engine Oil Sample - Obtain
D7R Track-Type Bulldozer Cooling System Coolant Sample (Level 1) - Obtain
C27 and C32 Engines for Caterpillar Built Machines Intake Manifold Air Pressure Is Low
C27 and C32 Engines for Caterpillar Built Machines NRS Exhaust Gas Temperature Is High
D6R2 Track-Type Tractor Engine Supplement Fan - Remove and Install
D6R2 Track-Type Tractor Engine Supplement Engine Side Guards - Remove and Install
Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357} Procedure For Updating A 3 Bank Implement Hydraulic System To A 4 Bank Implement Hydraulic System {5051, 5057, 5161, 5170, 5357}
D7E Track-Type Tractor Systems Air Conditioner
926M, 930M and 938M Wheel Loaders Power Train Tire and Rim - Remove and Install
2014/11/03 New Replacement Parts for the Torque Converter Are Now Used on Certain Large Wheel Loaders, Wheel Dozers, and Landfill Compactors {3101, 3105}
C27 and C32 Engines for Caterpillar Built Machines Data Link Configuration Status - Test
621K Wheel Tractor-Scraper Sound Information and Vibration Information
D7R Track-Type Bulldozer Winch Fairlead Rollers - Lubricate - If Equipped
D7R Track-Type Bulldozer Fuel Tank Water and Sediment - Drain
335F CR Excavator C7.1 Engine Supplement Pressure Sensor (Cooled Exhaust Gas) - Remove and Install - Differential Pressure Sensor and Absolute Pressure Sensor
926M, 930M and 938M Wheel Loaders Power Train Fixed Axle (Front) - Remove and Install
2014/12/09 An Improved SystemOne Self Cleaning Track Shoe is Now Available for Certain D6N and D6M Track-Type Tractors {4170}
D6R2 Track-Type Tractor Engine Supplement Fan Drive - Remove and Install
D7R Track-Type Bulldozer Fuel System - Prime
2014/10/27 Improved Solenoid Valve Group Is Now Used On Certain Load Haul Dumps and Wheel Loaders {3073, 3139, 5479}
335F CR Excavator C7.1 Engine Supplement Turbocharger - Remove and Install
D7E Track-Type Tractor Systems Bank Valve (Two)
D7E Track-Type Tractor Systems Bank Valve (Two)
D7E Track-Type Tractor Systems Bulldozer Brace