An Improved Window Guide and Rail Are Now Being Used on Certain Wheel Loaders {7310}
- Wheel Loader:
- 950H (S/N: MXL1-UP; JLX1-UP)
- 962H (S/N: SSA1-UP; PCW1-UP)
- 966H (S/N: BJ61-UP; BS61-UP)
- 972H (S/N: NPE1-UP; WXZ1-UP)
- 980H (S/N: PF81-UP)
- 986H (S/N: L8S1-UP)
Description of Change: The improved rail and guide will improve the function of the cab window group.
Adaptable To: The new 469-0238 Rail and 469-0237 Guide are adaptable to the following machines:
- 950H (S/N: JXL1-575)
- 950H (S/N: MXL1-1053)
- 962H (S/N: PCW1-304)
- 962H (S/N: SSA1-329)
- 966H (S/N: BJ61-790)
- 966H (S/N: BS61-201)
- 972H (S/N: NPE1-201)
- 972H (S/N: WXZ1-219)
- 980H (S/N: PF81-279)
- 986H (S/N: L8S1-281)
- 950H (S/N: JXL576-UP)
- 950H (S/N: MXL1054-UP)
- 962H (S/N: PCW305-UP)
- 962H (S/N: SSA330-UP)
- 966H (S/N: BJ6791-UP)
- 966H (S/N: BS6202-UP)
- 972H (S/N: NPE202-UP)
- 972H (S/N: WXZ220-UP)
- 980H (S/N: PF8280-UP)
- 986H (S/N: L8S282-UP)
Show/hide table
Required Parts     | ||||
---|---|---|---|---|
Part     | Qty     | Part No.     | Part Name     | Former Part No.     |
(1)     | 1     | 469-0238     | Rail     | 394-6529     |
(2)     | 1     | 469-0237     | Guide     | 394-5936     |
Installation Procedure
- Move machine to a hard level service. Apply the parking brake and turn key switch to the OFF position
- Using a screw driver press inward on the 394-5936 Slider (A) until the slide can be moved in the direction indicated in 1. Pull the slider 394-5936 Slider (A) out of 384-6529 Rail (B) Using pliers, break the slider (A) out from the window frame.
Show/hide table
NOTICE |
---|
Care must be taken during the removal and installation of the rail and slide as the window can be broken. |
Show/hide table
Illustration 1 | g03737527 |
- Remove the 384-6530 Sliding Glass and the rail (B) from the cab. Place the glass on a clean flat surface. Using a pliers or other compressing devise squeeze the bottom of the rail (B), the rail can now be pulled away from the window. Repeat until the entire length of the rail has been loosened. Remove the rail (B) from the glass. Clean the glass of all debris.
Show/hide table
Illustration 2 | g03737539 |
- Apply a 3 mm (0.12 inch) bead, of an approved glass adhesive, to the new rail (1). Leave a 5 mm (0.20 inch) gap of adhesive from the end of the rail (1). Insert glass into rail (1) as shown in Illustration 3. The glass should align with the end of the rail (1) opposite the latch end of the window. Press rail (1) until the rail (1) is in contact with the entire length of the glass. Allow the adhesive to cure before continuing to Step 5.
Show/hide table
Illustration 3 | g03737580 |
- Install the glass with the new rail (1) into the 372-6246 Cab Window Gp .
- Place the guide (2) into a minimum of 80° C (176.00000° F), for 1 minute.
- Install the guide (2) onto the window frame, as shown in Illustration 4. The guide (2) will need to be tilted for proper installation.
Show/hide table
Illustration 4 | g03737897 |
- Press the guide (2) in the direction indicated, to allow the guide (2) to go into the rail (1). Lock the window for a minimum of 4 hours to allow adhesive to cure.
Show/hide table
Illustration 5 | g03737926 |
Caterpillar Information System:
335F CR Excavator C7.1 Engine Supplement Hood - Remove and Install - Engine
2014/10/20 An Improved Single Tilt Brace Is Now Used On Certain D9R and D9T Track-Type Tractors {6050, 6061}
335F CR Excavator C7.1 Engine Supplement Flexible Exhaust Pipe - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Coolant Flow - Test
C27 and C32 Engines for Caterpillar Built Machines Aftertreatment Identification Module - Test
335F CR Excavator C7.1 Engine Supplement Soot Sensor - Remove and Install
Fuel Lines Rework on Certain D11T Tier 2 Track-Type Tractors{1274} Fuel Lines Rework on Certain D11T Tier 2 Track-Type Tractors{1274}
D7E Track-Type Tractor Engine Supplement Hood - Remove and Install
D7E Track-Type Tractor Engine Supplement Pump Drive - Remove and Install
335F CR Excavator C7.1 Engine Supplement Engine Oil Cooler - Remove and Install
335F CR Excavator C7.1 Engine Supplement Fuel Cooler - Remove and Install
980L Medium Wheel Loader Power Train, Steering, Braking, Hydraulic, and Machine Systems Steering Pump
2015/01/27 New Engine Software Is Used For Certain D11 Track-Type Tractors {1920, 7620}
A New Autolube Pump and Internal Circuit Board Are Now Available for Certain Wheel Loaders and Articulated Trucks {1408, 7516, 7540, 7610, 7620} A New Autolube Pump and Internal Circuit Board Are Now Available for Certain Wheel Loaders and Articulated Trucks {1408, 7516, 7540, 7610, 7620}
D3K2, D4K2 and D5K2 Track-Type Tractor Systems Electronic Control (Power Train System)
D7E Track-Type Tractor Engine Supplement Access Doors/Covers - Remove and Install
335F CR Excavator C7.1 Engine Supplement Hood - Remove and Install - Clean Emissions Module
335F CR Excavator C7.1 Engine Supplement Clean Emissions Module - Remove and Install
926M, 930M and 938M Wheel Loaders Machine Systems Window Wiper and Wiper Motor (Front) - Remove and Install
D7E Track-Type Tractor Engine Supplement Turbocharger - Remove and Install
926M, 930M and 938M Wheel Loaders Machine Systems Window Wiper and Wiper Motor (Rear) - Remove and Install
930K Wheel Loader Machine Systems Refrigerant Accumulator - Remove and Install
2014/10/15 Reversing Fan Motor Break-In Procedure On Certain D6K2 Track-Type Tractors That Are Equipped With A Reversing Fan {1356, 1386}
2014/10/21 Improved Engine Harness Assembly Routing Is Now Used on Certain D6N Track-Type Tractors {1000, 1408}