Window Wiper and Wiper Motor (Front) - Remove and Install
Removal Procedure
Start By:
- Remove the steering column.
- Disconnect hose (1) .
Show/hide table
Illustration 1 | g02809656 |
- Remove bolts (2) from wiper arm (3) and wiper arm (4). Remove wiper arms (3) and (4) .
- Remove shaft seals (5) .
Show/hide table
Illustration 2 | g02809677 |
- Remove nuts (7) and nuts (6) .
Show/hide table
Illustration 3 | g02809758 |
- Remove plastic washers (8) .
Show/hide table
Illustration 4 | g02809798 |
- Remove rubber washers (9) .
Show/hide table
Illustration 5 | g02809817 |
- Disconnect harness assembly (11). Remove wiper motor assembly (10) .
Show/hide table
Illustration 6 | g02809819 |
- Remove bolt (12). Remove bolts (15). Remove wiper motor (13) from bracket assembly (14) .
Show/hide table
Illustration 7 | g02809858 |
Installation Procedure
- Install wiper motor (13) in the reverse order of removal.
- Tighten nuts (6) to a torque of 13 ± 2 N·m (115 ± 18 lb in).
- Tighten nuts (7) to a torque of 38 ± 2 N·m (28 ± 1 lb ft)
Note: Be sure to hold nuts (6) steady while tightening nuts (7) .
- Tighten nuts (2) to a torque of 14 ± 2 N·m (124 ± 18 lb in).
Caterpillar Information System:
335F CR Excavator C7.1 Engine Supplement Clean Emissions Module - Remove and Install
335F CR Excavator C7.1 Engine Supplement Hood - Remove and Install - Clean Emissions Module
D7E Track-Type Tractor Engine Supplement Access Doors/Covers - Remove and Install
D3K2, D4K2 and D5K2 Track-Type Tractor Systems Electronic Control (Power Train System)
A New Autolube Pump and Internal Circuit Board Are Now Available for Certain Wheel Loaders and Articulated Trucks {1408, 7516, 7540, 7610, 7620} A New Autolube Pump and Internal Circuit Board Are Now Available for Certain Wheel Loaders and Articulated Trucks {1408, 7516, 7540, 7610, 7620}
2015/01/27 New Engine Software Is Used For Certain D11 Track-Type Tractors {1920, 7620}
2015/03/12 An Improved Window Guide and Rail Are Now Being Used on Certain Wheel Loaders {7310}
335F CR Excavator C7.1 Engine Supplement Hood - Remove and Install - Engine
2014/10/20 An Improved Single Tilt Brace Is Now Used On Certain D9R and D9T Track-Type Tractors {6050, 6061}
335F CR Excavator C7.1 Engine Supplement Flexible Exhaust Pipe - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Coolant Flow - Test
C27 and C32 Engines for Caterpillar Built Machines Aftertreatment Identification Module - Test
D7E Track-Type Tractor Engine Supplement Turbocharger - Remove and Install
926M, 930M and 938M Wheel Loaders Machine Systems Window Wiper and Wiper Motor (Rear) - Remove and Install
930K Wheel Loader Machine Systems Refrigerant Accumulator - Remove and Install
2014/10/15 Reversing Fan Motor Break-In Procedure On Certain D6K2 Track-Type Tractors That Are Equipped With A Reversing Fan {1356, 1386}
2014/10/21 Improved Engine Harness Assembly Routing Is Now Used on Certain D6N Track-Type Tractors {1000, 1408}
2015/07/22 Improved Tube and Mounting Bracket are Now Used on Certain 988K Wheel Loaders {4257, 5057}
3512E Tier 4 Final Engines for Land Electric Drilling Electrical Power Supply - Test
C175-16 Locomotive Engine Clean Emissions Module Has High Oxygen Level
926M, 930M and 938M Wheel Loaders Machine Systems Steering Cylinder - Remove and Install
930K Wheel Loader Machine Systems Brake Accumulator - Remove and Install
C280 Marine Engines Exhaust Differential Temperature Is High
926M, 930M and 938M Wheel Loaders Machine Systems Brake Control Valve (Service) - Remove and Install