Hood Panels (Front and Rear) - Remove and Install
Start By:
- Remove hood.
Note: The hood must be removed from the machine to remove panels. If not, the hood support could warp and become damaged.
Note: The supports illustrated in the Disassembly and Assembly, "Hood - Remove and Install" have been removed in this story for photographic purposes.
- Remove bolts (1). Remove bolts (3) and repeat for the other side.
- Use two people to remove top hood panel (1).
Show/hide table
Illustration 2 g03392632 - Remove nuts (5). Remove left side hood panel (4). Repeat for the right side hood panel.
Show/hide table
Illustration 3 g02476699 - Remove bolts (7), (8), and (9). Use two people to remove right side panel (6). Repeat for the left side panel.
Show/hide table
Illustration 4 g02476712 - Remove bolts (10) and (11). Repeat for the other side
- Use two people to remove top panel assembly (12).
Show/hide table
Illustration 5 g02476714 - Remove bolts (16) and repeat for the other side. Remove nuts (15) and screws (13).
- Use two people to remove rear panel assembly (14).
Show/hide table
Illustration 1 | g03392628 |
- Install the panels in the reverse order of removal.
Caterpillar Information System:
990K Wheel Loader Radiator Core - Clean
D-Series and D2-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Alert Indicators
D10T2 Track-Type Tractor Monitoring System
990K Wheel Loader Receiver Dryer (Refrigerant) - Replace
2013/04/22 An Improved Steering lines Group and Air Lines Group is Now Used on Certain D6N Track-Type Tractors {1071, 4104, 4133, 4304}
966H and 972H Wheel Loaders Steering System Piston Pump (Steering)
D10T2 Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
966H and 972H Wheel Loaders Power Train Solenoid Valve (Differential Lock)
C9.3 Engines for Caterpillar Built Machines Unit Injector Sleeve - Remove and Install
C4.4 and C7.1 Engines Intake Manifold Air Pressure Is Low
990K Wheel Loader Circuit Breakers - Reset
990K Wheel Loader Hoses and Clamps - Inspect/Replace
Installation Instructions for 425-1892 Cold Weather Starting Ar for 966H and 972H Wheel Loader Machines{1450, 1450, 1456, 7610} Installation Instructions for 425-1892 Cold Weather Starting Ar for 966H and 972H Wheel Loader Machines{1450, 1450, 1456, 7610}
980M Tier 4 and 982M Tier 4 Wheel Loaders Belt Tensioner - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Alternator - Remove and Install
836K Landfill Compactor and 834K Wheel Dozer Sensor Signal (Analog, Passive) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel - Remove and Install
980L Tier 3 Wheel Loader Engine Supplement Fuel Transfer Pump - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Fuel Manifold (ARD) - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Ignition Coil - Remove and Install - Clean Emissions Module
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Service and Parking Brake
C9.3 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install