Crankshaft Front Seal - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7600 | Slide Hammer Puller | 1 |
| B | 1U-8145 | Drill Bit | 1 |
| C | 1U-7430 | Front Seal Installer | 1 |
Start By:
- Remove the vibration damper and pulley.
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (B) to drill three evenly spaced holes in crankshaft front seal (1).
- Alternate between the drilled holes and use Tooling (A) to remove crankshaft front seal (1).
Show/hide table
| |
| Illustration 1 | g01138207 |
Note: Use caution when drilling near the crankshaft.
- Use Tooling (C) to install crankshaft front seal (1).
- Lightly lubricate the inner diameter of the crankshaft seal with liquid soap prior to installing the crankshaft pulley
Show/hide table
| |
| Illustration 2 | g01138218 |
Note: The crankshaft seal is a dry installation.
End By:
- Install the vibration damper and pulley.
Caterpillar Information System:
621K, 623K, and 627K Wheel Tractor-Scrapers Systems Service and Parking Brake
980M Tier 4 and 982M Tier 4 Wheel Loaders Ignition Coil - Remove and Install - Clean Emissions Module
C9.3 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Fuel Manifold (ARD) - Remove and Install - Clean Emissions Module
980L Tier 3 Wheel Loader Engine Supplement Fuel Transfer Pump - Remove and Install
C9.3 Engines for Caterpillar Built Machines Flywheel - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Fuel Priming Pump and Primary Filter (Water Separator) - Remove and Install
836K Landfill Compactor and 834K Wheel Dozer Sensor Signal (Analog, Passive) - Test
980M Tier 4 and 982M Tier 4 Wheel Loaders Alternator - Remove and Install
980M Tier 4 and 982M Tier 4 Wheel Loaders Belt Tensioner - Remove and Install
Installation Instructions for 425-1892 Cold Weather Starting Ar for 966H and 972H Wheel Loader Machines{1450, 1450, 1456, 7610} Installation Instructions for 425-1892 Cold Weather Starting Ar for 966H and 972H Wheel Loader Machines{1450, 1450, 1456, 7610}
980M Tier 4 and 982M Tier 4 Wheel Loaders Hood Panels (Front and Rear) - Remove and Install
2013/03/15 Improved Process for Filling the Cooling System on D3500 Generator Sets and Power Modules {1350}
D10T2 Track-Type Tractor Hydraulic System Filter Bypass Screen - Clean
D10T2 Track-Type Tractor Capacities (Refill)
D10T2 Track-Type Tractor Lubricant Viscosities - Fluids Recommendations
D10T2 Track-Type Tractor Additional Messages
D10T2 Track-Type Tractor Sound Information and Vibration Information
D10T2 Track-Type Tractor Specifications
C9.3 Engines for Caterpillar Built Machines Housing (Front) - Remove and Install
C9.3 Engines for Caterpillar Built Machines Compression Brake - Remove and Install
C9.3 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove and Install
C9.3 Engines for Caterpillar Built Machines Camshaft - Remove and Install
C9.3 Engines for Caterpillar Built Machines Cylinder Liner - Remove and Install