Steering Control Support
Show/hide table
 | |
| Illustration 1 | g02352120 |
(1) Torque for the two screws ... 6 ± 1 N·m (55 ± 9 lb in)
Show/hide table
 | |
| Illustration 2 | g02352134 |
Top view | |
(2) Torque for the three screws ... 6 ± 1 N·m (55 ± 9 lb in)
Show/hide table
 | |
| Illustration 3 | g01126612 |
(3) Torque for the screw ... 6 ± 1 N·m (55 ± 9 lb in)
(4) Torque for the two screws ... 6 ± 1 N·m (55 ± 9 lb in)
Show/hide table
 | |
| Illustration 4 | g01126609 |
(5) Washers
(6) Spring
- Solid Length ... 12.8 mm (0.5 inch)
- Assembled Length ... 16.8 mm (0.66 inch)
- Load at Assembled Length ... 102 ± 8 N (30 ± 2 lb)
- Free Length After Test ... 22.48 mm (0.885 inch)
- Assembled Length ... 16.8 mm (0.66 inch)
Show/hide table
 | |
| Illustration 5 | g01046670 |
(1) Jam nut. (2) Lever. (3) Guide. (4) Pin. (5) Pin. (6) Washer. (7) Spacer. (8) Spring. (9) Bolt. | |
Use the following procedures in order to compress spring (8) when you are assembling the support.
- Move lever (2) so that a 7 mm (0.275 inch) bar can be installed between pin (5) and the top of guide (3) .
- Release the lever. Turn bolt (9) until spacer (7) contacts washers (6) at both ends. Lock the bolt by using the jam nut (1). Remove the 7 mm (0.275 inch) bar.
Caterpillar Information System:
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning System Electrical Schematic
2010/12/20 New High Intensity Discharge Flood Lamp Groups Are Now Used on Certain Cat Products {1434}
992K Wheel Loader Machine Systems Piston Pump (Steering) - Remove and Install
D6T Track-Type Tractor Electronic Control Systems Electronic Control Module (ECM) - Configure
2010/12/16 A New Top Liner Seal Is Used on 3500 Engines {1201, 7555}
966K XE Wheel Loader Power Train Transmission Control - Includes Transmission Controls
2011/03/04 Improved Tilt Cylinder Pin Assembly Procedure Reduces Tilt Line Fouling {5057, 5104}
966K Wheel Loader Cooling System Coolant (ELC) - Change
D8T Track-Type Tractor Tracks
D6T Track-Type Tractor Power Train Lubrication Distribution Valve - Remove and Install
D6T Track-Type Tractor Power Train Pivot Shaft - Remove and Install
950K and 962K Wheel Loaders Camera - Clean
D6T Track-Type Tractor Machine Systems Case and Frame
D6T Track-Type Tractor Engine including Specifications Cylinder Liner
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning and Heating System Relay Operation
994H Wheel Loader Power Train Transmission - Remove
994H Wheel Loader Power Train Transmission - Install
D6T Track-Type Tractor Machine Systems including Specifications Refrigerant Condenser
D6T Track-Type Tractor Machine Systems including Specifications Tilt Cylinder (Bulldozer) - VPAT
AD55 Underground Articulated Truck Braking System Solenoid Valve (Retarder Control)
AD30 Underground Articulated Truck Torque Converter - Disassemble
D8T Track-Type Tractor Power Train Track Roller - Double Flange
D8T Track-Type Tractor Power Train Track Roller - Single Flange
D8T TRACK-TYPE TRACTORS Machine Systems Sweep Group