Electronic Control Module (ECM) - Configure
Show/hide table
| Required Tools | ||
| Part Number | Description | Quantity |
| JEBD3003 | Caterpillar Electronic Technician (Cat ET) | 1 |
| 317-7485 | Communication Adapter-3 As | 1 |
| 327-8981 | Adapter Cable As
(CA3 to Service Tool) |
1 |
| 370-4617 | Adapter Cable As
(CA3 to PC USB) |
1 |
| 317-7484 | Communication Adapter-3 Kit
(Incl. Communication Adapter-3 As, two Cables listed above) |
1 |
The Caterpillar Electronic Technician (Cat ET) is used to access the configuration screen . A message on the Cat ET screen will give instructions that guide the user through the procedure. Refer to the manual that is provided with the Cat ET software for more information about Cat ET.
The Electronic Control Module (ECM) must be configured when the ECM has been replaced. The ECM must be configured before a calibration can be started.
A check of the configuration screen could resolve a problem with the machine. A problem with a component could be identified as one of the following items:
- A component is not installed.
- A component is installed, but a change to the installation is needed in order to correct a problem.
Follow these instructions to get to the configuration screen:
- Connect the communications adapter and the computer to the diagnostic service tool connector.
- Start the Caterpillar Electronic Technician (Cat ET).
- Select "File". Go to "Select ECM". Choose the appropriate ECM.
- Go to the "Service" Menu. Select "Configurations". Click "OK". Certain operations or characteristics can be changed.
Caterpillar Information System:
2010/12/16 A New Top Liner Seal Is Used on 3500 Engines {1201, 7555}
966K XE Wheel Loader Power Train Transmission Control - Includes Transmission Controls
2011/03/04 Improved Tilt Cylinder Pin Assembly Procedure Reduces Tilt Line Fouling {5057, 5104}
966K Wheel Loader Cooling System Coolant (ELC) - Change
D8T Track-Type Tractor Tracks
D6T Track-Type Tractor Power Train Lubrication Distribution Valve - Remove and Install
D6T Track-Type Tractor Power Train Pivot Shaft - Remove and Install
950K and 962K Wheel Loaders Camera - Clean
950K and 962K Wheel Loaders Roading Fender Control - If Equipped
D8T Track-Type Tractor Power Train Suction Screen
D6T Track-Type Tractor Hydraulic System Control Manifold - Pilot
D6T Track-Type Tractor Hydraulic System Cylinder Mounting
992K Wheel Loader Machine Systems Piston Pump (Steering) - Remove and Install
2010/12/20 New High Intensity Discharge Flood Lamp Groups Are Now Used on Certain Cat Products {1434}
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning System Electrical Schematic
994H Wheel Loader Steering System Steering Control Support
D6T Track-Type Tractor Machine Systems Case and Frame
D6T Track-Type Tractor Engine including Specifications Cylinder Liner
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning and Heating System Relay Operation
994H Wheel Loader Power Train Transmission - Remove
994H Wheel Loader Power Train Transmission - Install
D6T Track-Type Tractor Machine Systems including Specifications Refrigerant Condenser
D6T Track-Type Tractor Machine Systems including Specifications Tilt Cylinder (Bulldozer) - VPAT
AD55 Underground Articulated Truck Braking System Solenoid Valve (Retarder Control)