Improved Tilt Cylinder Pin Assembly Procedure Reduces Tilt Line Fouling {5057, 5104}
- Wheel Loader:
- 994F (S/N: 4421-UP)
Description of Change: An improved tilt cylinder pin assembly procedure is now available for 994 Wheel Loader. The improved tilt cylinder assembly procedure reverses bolt thread and nut direction to the outside of the machine. This improved pin installation reduces tilt line fouling
Adaptable To: The improved tilt cylinder pin assembly procedure is adaptable to the following machines.
- 4421-324
- 442325-UP
Required Parts
Show/hide table
Part Order List     | ||
Qty     | Part Number     | Descriptioni     |
2     | 3E-8009     | Bolt     |
2     | 358-7033     | Inside Collet     |
Show/hide table
Illustration 1 | g02352012 |
- Reuse two 8R-3913 Outside Collets still used on the outside.
Show/hide table
Illustration 2 | g02352003 |
(1) 3E-8009 Bolt (2) 5P-2322 Lip Type Seal (3) 8R-3913 Outside Collet (4) 358-7033 Inside Collet |
- Reuse washers, plugs, nuts, and pins.
- Remove the 3E-8009 Bolt and the inside 8R-3913 Collet .
- Install the updated 358-7033 Collet .
- Install the 3E-8009 Bolt (making sure the bolt thread and nut face the outside of the machine).
Note: Follow torque procedure in Special Instruction, REHS1789.
- After installing pins, measure gap between pin and inside face of new collet. Use puller hole access. The gap should be at least 3 mm (0.12 inch) or more. 6 mm (0.24 inch) nominal.
Show/hide table
Illustration 3 | g02352006 |
Caterpillar Information System:
966K Wheel Loader Cooling System Coolant (ELC) - Change
D8T Track-Type Tractor Tracks
D6T Track-Type Tractor Power Train Lubrication Distribution Valve - Remove and Install
D6T Track-Type Tractor Power Train Pivot Shaft - Remove and Install
950K and 962K Wheel Loaders Camera - Clean
950K and 962K Wheel Loaders Roading Fender Control - If Equipped
D8T Track-Type Tractor Power Train Suction Screen
D6T Track-Type Tractor Hydraulic System Control Manifold - Pilot
D6T Track-Type Tractor Hydraulic System Cylinder Mounting
2010/12/20 "Heavy Duty" Angle Cylinder Seal Is Available For D3K, D4K, And D5K {5101}
D6T Track-Type Tractor Hydraulic System Quick-Drop Valve
2011/04/22 A New Speed Sensor Group Is Now Available for Certain D3G, D4G, D5G, D3K, D4K, and D5K Small Track-Type Tractors {1907}
966K XE Wheel Loader Power Train Transmission Control - Includes Transmission Controls
2010/12/16 A New Top Liner Seal Is Used on 3500 Engines {1201, 7555}
D6T Track-Type Tractor Electronic Control Systems Electronic Control Module (ECM) - Configure
992K Wheel Loader Machine Systems Piston Pump (Steering) - Remove and Install
2010/12/20 New High Intensity Discharge Flood Lamp Groups Are Now Used on Certain Cat Products {1434}
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning System Electrical Schematic
994H Wheel Loader Steering System Steering Control Support
D6T Track-Type Tractor Machine Systems Case and Frame
D6T Track-Type Tractor Engine including Specifications Cylinder Liner
312E, 312F, 313F, 316E, 316F, 318E, 318F, 320E, 320F, 323E, 323F, 324E, 325F, 326F, 329E, 329F, 330F, 335F, 336E, 336F, 340F, 349E, 349F, 352F, 374F and 390F Excavators and 336E MHPU and 349E MHPU Mobile Hydraulic Power Units Air Conditioning and Hea Air Conditioning and Heating System Relay Operation
994H Wheel Loader Power Train Transmission - Remove
994H Wheel Loader Power Train Transmission - Install