Fuel Transfer Pump
Show/hide table
Illustration 1 | g01621126 |
(3) Check valve (4) Cap |
When the fuel transfer pump group is viewed from the drive end, the drive gear rotates in the clockwise direction.
Minimum output ... 21 L/min (5.5 US gpm)
Minimum output is attained under the following conditions:
Pump pressure ... 415 kPa (60 psi)
Pump speed ... 2400 rpm
Minimum cracking pressure of bypass valve ... 620 kPa (90 psi)
Maximum pressure of fully open bypass valve ... 965 kPa (140 psi)
(1) Dimensions for terminal bushing
- Inside diameter of the terminal bushing for gear shaft ... 12.783 mm (0.5033 inch)
- Installation depth of terminal bushing ... 1.5 ± 0.5 mm (0.06 ± 0.02 inch)
(2) Dimensions for drive shaft assembly
- Diameter of the shaft ... 12.700 to 12.675 mm (0.5000 to 0.4990 inch)
- Diameter of the gear ... 29.801 ± 0.006 mm (1.1733 ± 0.0002 inch)
- Length of the gear ... 25.347 ± 0.008 mm (0.9979 ± 0.0003 inch)
- Diameter of the gear ... 29.801 ± 0.006 mm (1.1733 ± 0.0002 inch)
(5) Dimensions for idler gear assembly
- Diameter of the gear ... 29.801 ± 0.006 mm (1.1733 ± 0.0002 inch)
- Length of the gear ... 25.347 ± 0.008 mm (0.9979 ± 0.0003 inch)
(6) 1W-4655 Relief Valve Spring
- Free length ... 28.4 mm (1.12 inch)
- Outside diameter ... 10.7 mm (0.42 inch)
Caterpillar Information System:
2008/09/15 Improved Engine Side Panels Are Now Used {7267}
2008/09/22 New Pin Within A Pin Improves Retention of Planetary Shaft {4011}
3500 Generator Sets Generator Load - Check
C9 Engine and D7E Track-Type Tractors Injector Trim File - Install
2008/10/13 An Improved Track Bushing Is Now Used {4169, 4171}
3408E and 3412E Engines for Caterpillar Built Machines Flywheel Housing
TS185 and TS225 Towed Scrapers Machine Systems Ejector Clearance - Check and Adjust
TS185 and TS225 Towed Scrapers Machine Systems Service Brake (Scraper)
953D, 963D and 973D Track-Type Loaders Monitoring System Menus (Instrument Cluster)
613G Wheel Tractor-Scraper Power Train Transfer Gear End Play - Adjust
Installation of Regeneration Circuit for Tilt Cylinder for Machine with 3.6 Meter Boom{1408, 5057, 5104, 512R} Installation of Regeneration Circuit for Tilt Cylinder for Machine with 3.6 Meter Boom{1408, 5057, 5104, 512R}
C9 Engine and D7E Track-Type Tractors Electronic Service Tool Does Not Communicate
2008/09/22 The Routing of the Lines in the Power Train Oil Lines Group have been Updated {3016, 3024}
Installation Instructions for the 330-0822 Control Arrangement (Variable Pitch Fan) (Kit){107P, 1356, 1386, 138R, 7332} Installation Instructions for the 330-0822 Control Arrangement (Variable Pitch Fan) (Kit){107P, 1356, 1386, 138R, 7332}
914G2 and IT14G2 Compact Wheel Loaders Mirror - If Equipped
Incorrect Wiring For AccuGrade On D6K And D6N Track-Type Tractors{1408, 7220} Incorrect Wiring For AccuGrade On D6K And D6N Track-Type Tractors{1408, 7220}
613G Wheel Tractor-Scraper Power Train Transmission Pressures - Test and Adjust
613G Wheel Tractor-Scraper Chassis Electronic Control System Diagnostic Code List
993K Wheel Loader Machine Systems Hydraulic Tank (Steering) (Brake) - Disassemble
993K Wheel Loader Machine Systems Hydraulic Tank (Steering) (Brake) - Assemble
993K Wheel Loader Machine Systems Gear Pump (Steering Oil Cooler) - Disassemble
613G Wheel Tractor-Scraper Power Train Pressure Differential Valve (Transmission) - Test
993K Wheel Loader Machine Systems Gear Pump (Steering Oil Cooler) - Assemble
993K Wheel Loader Machine Systems Piston Pump (Steering) (Center) - Disassemble