Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
- 拆下水温调节器壳体。 请参阅拆解和组装, "水温调节器 - 拆卸和安装"。
- 拆下锁紧螺母 (2) 和隔套 (1) 。
Show/hide table
图 1 | g01237525 |
- 将排气歧管作为一个整体拆下。
- 将排气歧管 (4) 从排气歧管 (3) 上拆下。
- 拆下排气歧管密封垫 (5) 。
- 如有必要,将拔梢锁紧双头螺柱从缸盖上拆下。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 5P-3931     | 防粘结剂     | -     |
B     | 2P-2333     | 高温密封胶     | -     |
C     | 165-4638     | 导管     | 3     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将拔梢锁紧双头螺柱安装在缸盖上并拧紧至扭矩为 35 ± 5 N·m (26 ± 4 lb ft)。
- 将清洁的发动机机油涂抹在排气歧管 (3) 的凹端上。 将工具 (B) 涂抹在排气歧管 (4) 的凸端上。 组装排气歧管 (4) 和 (3) 。 清除组装好的接头上多余的密封胶。
Show/hide table
图 2 | g01237553 |
- 将排气歧管密封垫 (5) 安装在拔梢锁紧双头螺柱上。
- 将工具 (C) 安装在位置 "X" 处的拔梢锁紧双头螺柱上。
- 将排气歧管安装在工具 (C) 上以便对准排气歧管。 将隔套 (1) 安装在拔梢锁紧双头螺柱上。
- 将工具 (A) 涂抹在拔梢锁紧双头螺柱的螺纹上。 安装并用手拧紧锁紧螺母 (2) 。
注: 使用后请丢弃锁紧螺母。 安装时请使用新的锁紧螺母。
- 拆下工具 (C) 并安装剩余隔套。 将工具 (A) 涂抹在拔梢锁紧双头螺柱的螺纹上,安装并用手拧紧锁紧螺母。
- 以图 3 所示的数字顺序拧紧锁紧螺母 (2) 。 拧紧锁紧螺母 (2) 至扭矩为 38 ± 5 N·m (28 ± 4 lb ft)。
Show/hide table
图 3 | g01100255 |
End By:
- 安装水温调节器壳体 3。 请参阅 拆解和组装, "水温调节器 - 拆卸和安装"。
- 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Turbocharger - Assemble
C15 and C18 Generator Set Engines Turbocharger - Disassemble
Oil Pan and Gasket{1302, 1302} Oil Pan and Gasket{1302, 1302}
2010/09/01 Cylinder Pack Upgrade Is Available for Certain 3406B and 3406C Engines When Replacing All Six Cylinders Packs {1201, 1225}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission Shifting Function
CX31 On-Highway Transmission Transmission Oil Sample - Obtain
CX31 On-Highway Transmission Transmission Oil Level - Check
CX31 On-Highway Transmission Transmission Oil - Change
CX31 On-Highway Transmission Transmission Warm-up
CX31 On-Highway Transmission Transmission Control
3126B and 3126E Truck Engines Electronic Control Wiring Group
Check Engine Light ON with No Active Fault Codes for 3126E Engines{1901, 1902, 7431, 7620} Check Engine Light ON with No Active Fault Codes for 3126E Engines{1901, 1902, 7431, 7620}
C3.3 Industrial Engine Air in Fuel - Test
C3.3 Industrial Engine Fuel Injector - Remove
Procedure for Testing the 167-1709 Pressure Sensor Gp on the 3126 Industrial Engine{1718, 1916, 1917, 1923, 1924, 1925} Procedure for Testing the 167-1709 Pressure Sensor Gp on the 3126 Industrial Engine{1718, 1916, 1917, 1923, 1924, 1925}
3126B and 3126E Truck Engines Air Compressor - Midland Air Compressors
2006/02/13 Enhanced Voltmeter Leads Are Now Available {0785}
G3500 A3 Engines Replacing the ECM
2006/02/01 Troubleshooting Engines with Mechanical Unit Injection (MUI) {1290, 7569}
3126B and 3126E Truck Engines Air Compressor - Midland Air Compressors
C15 and C18 Generator Set Engines Engine Oil Filter Base - Remove
G3500 A3 Engines Symptoms
G3500 A3 Engines Electronic Service Tool Will Not Communicate with ECM
C7 Marine Engines Crankshaft Rear Seal and Wear Sleeve - Remove