Air Compressor - Midland Air Compressors
Show/hide table
Illustration 1 | g01237622 |
(1) Air compressor
(2) Nut
Perform the following steps in order to properly tighten the nut:
- Tighten the nut to a torque of 160 ± 15 N·m (120 ± 11 lb ft).
- Use a soft faced hammer and a 213-3530 Socket and tap the gear one time. Tighten the nut to a torque of 160 ± 15 N·m (120 ± 11 lb ft).
(3) Gear
(4) Bolt
Tighten the bolt that holds the air compressor line on engines that are equipped with this hose assembly. Tighten the bolt to the following torque. ... 28 ± 7 N·m (21 ± 5 lb ft)
Use the following procedure to mount the air compressor.
- Install two bolts (A) and tighten the bolts to a torque of 100 ± 20 N·m (75 ± 15 lb ft).
- Install the following four bolts finger tight: (B), (C) and (D) .
- Tighten one bolt (B) to a torque of 50 ± 10 N·m (37 ± 7 lb ft).
- Tighten two bolts (C) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
- Tighten one bolt (D) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Caterpillar Information System:
2006/02/01 Troubleshooting Engines with Mechanical Unit Injection (MUI) {1290, 7569}
G3500 A3 Engines Replacing the ECM
2006/02/13 Enhanced Voltmeter Leads Are Now Available {0785}
3126B and 3126E Truck Engines Air Compressor - Midland Air Compressors
Procedure for Testing the 167-1709 Pressure Sensor Gp on the 3126 Industrial Engine{1718, 1916, 1917, 1923, 1924, 1925} Procedure for Testing the 167-1709 Pressure Sensor Gp on the 3126 Industrial Engine{1718, 1916, 1917, 1923, 1924, 1925}
C3.3 Industrial Engine Fuel Injector - Remove
C3.3 Industrial Engine Air in Fuel - Test
C15 and C18 Generator Set Engines Exhaust Manifold - Remove and Install
C15 and C18 Generator Set Engines Turbocharger - Assemble
C15 and C18 Generator Set Engines Turbocharger - Disassemble
Oil Pan and Gasket{1302, 1302} Oil Pan and Gasket{1302, 1302}
2010/09/01 Cylinder Pack Upgrade Is Available for Certain 3406B and 3406C Engines When Replacing All Six Cylinders Packs {1201, 1225}
C15 and C18 Generator Set Engines Engine Oil Filter Base - Remove
G3500 A3 Engines Symptoms
G3500 A3 Engines Electronic Service Tool Will Not Communicate with ECM
C7 Marine Engines Crankshaft Rear Seal and Wear Sleeve - Remove
3126B and 3126E Truck Engines Air Compressor - Midland Air Compressors
C15 and C18 Generator Set Engines Engine Oil Filter Base - Install
C7 Marine Engines Crankshaft Rear Seal and Wear Sleeve - Install
3500 Spark Ignited Engines Spark Plug and Transformer
2006/02/13 Test Harness Connects PC or Laptop Computer to Electronic Governor {0779, 0785, 1930, 7620}
G3500 A3 Engines Engine Starts but Stalls Immediately
C3.3 Industrial Engine Engine Crankcase Pressure (Blowby) - Test
C15 and C18 Generator Set Engines Engine Oil Filter Base - Disassemble