Water Temperature Control Valve - Install
安装步骤
- 将适当的起吊设备连接在温度控制阀 (8) 上。 温度控制阀 (8) 的重量约为 73 kg (160 lb)。 安置温度控制阀 (8) 。 安装螺栓 (12) 。 安置管组件 (19) 。 安装螺栓 (18) 。 将卡箍 (15) 滑到位并拧紧螺母 (14) 。 定位管组件 (17) 。 安置法兰 (13) 并安装螺栓 (16) 。
Show/hide table
图 1 | g01522919 |
- 安置管组件 (11) 。 安装螺栓 (10) 。
Show/hide table
图 2 | g01200797 |
- 连接线束组件 (7) 和 (9) 以安装温度控制阀 (8) 。
Show/hide table
图 3 | g01522904 |
- 安置箱体 (6) 。 安装螺栓 (5) 。
Show/hide table
图 4 | g01209826 |
- 安装螺栓 (4) 。
Show/hide table
图 5 | g01209825 |
- 连接线束组件 (2) 和 (3) 。
Show/hide table
图 6 | g01209824 |
- 连接线束组件 (1) 。
Show/hide table
图 7 | g01209822 |
- 向冷却系统加注冷却液。 请参考操作和保养手册, "冷却系统冷却液 - 更换"。
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Flywheel
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Oil Filter (Transmission)
C15 and C18 Engines for Caterpillar Built Machines Piston Cooling Jet
C7 Petroleum Engines Water Lines
CX31 On-Highway Transmission Modulating Valve
C7 Petroleum Engines Engine Oil Lines
TH31 Well Servicing Transmissions Bypass Valve - Remove and Install
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Assemble
330D, 336D, 336D2, 340D and 340D2 Excavators and 336D MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Disassemble
C7 Petroleum Engines Exhaust Elbow
C7 Petroleum Engines Exhaust Elbow
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Solenoid Valve (Negative Flow Control, Proportional Reducing Valve) - Install
C175 Generator Set Engines Electronic Control Module (Engine) - Remove and Install
TH48-E80 Petroleum Transmission General Information
TH31 Well Servicing Transmissions Modulating Valve (Transmission Clutch) - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Gear and Bearing - Remove
C11 and C13 Engines Water Pump
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Gear and Bearing - Install
TH31 Well Servicing Transmissions Modulating Valve (Torque Converter Lockup Clutch) - Remove and Install
345C Excavator and 345C MHPU Mobile Hydraulic Power Unit Machine Systems Control Valve (Counterweight Circuit) - Install
Removal and Installation of the 126-1774 Endbell Cover {7553} Removal and Installation of the 126-1774 Endbell Cover {7553}
3500 Engines Turbocharger
C27 and C32 Generator Set Engines Can Not Reach Top Engine RPM
C27 and C32 Generator Set Engines Engine Will Not Crank