Fuel Pressure Sensor - Remove and Install
Show/hide table
| 注意 |
|---|
|
在进行检验、保养、测试、调整及维修产品期间，必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前，要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品，请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开线束组件 (1)。
- 从燃油滤清器底座上拆下燃油压力传感器 (2)。
- 将 O 形密封圈从燃油压力传感器 (2) 上拆下。
Show/hide table
| |
| 图 1 | g01175571 |
Show/hide table
| 注意 |
|---|
|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将一个新的 O 形密封圈安装在燃油压力传感器 (2) 上。
- 安装燃油压力传感器 (2) 并上紧到
10 ± 2 N·m (89 ± 18 lb in) 的扭矩。 - 连接线束组件 (1)。
Show/hide table
|
| |
| 图 2 | g01175571 |
注: 检查 O 形密封圈有无磨损或损坏。 如有必要，更换O型密封圈。
Caterpillar Information System:
C32 Power Module Engine Air Cleaner Element (Dual Element) - Clean/Replace - If Equipped
C9 Engine for Caterpillar Built Machines Engine Oil Pressure Sensor - Remove and Install
3500 Industrial and Generator Set Engines Air Shutoff - Test
C9 Engine for Caterpillar Built Machines Coolant Temperature Sensor - Remove and Install
2005/08/29 New Exhaust Bellows Provide Improved Sealing of Exhaust Gas {1059}
TH48-E80 Petroleum Transmission Torque Converter
C15 and C18 Petroleum Generator Sets Electrical System
C7 PETROLEUM Petroleum Engine Atmospheric Pressure Sensor - Remove and Install
C18 Marine Generator Set Engines System Configuration Parameters
EMCPII+ for Gas Engines Shutdown Mode
3500 Generator Set Engines Cylinder Block
2005/06/01 An Improved Oil Drain Tube for the Turbocharger is Now Used {1052, 1307}
C9 Engine for Caterpillar Built Machines Injection Actuation Pressure Sensor - Remove and Install
325D and 329D Excavators Hydraulic System Solenoid Valve (Hydraulic Lockout)
C9 Engine for Caterpillar Built Machines Speed/Timing Sensor - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Piston Motor (Hydraulic Fan) - Disassemble
345C MHPU Mobile Hydraulic Power Unit Machine Systems Piston Motor (Hydraulic Fan) - Assemble
XQ60 Rental Generator Set Product Lifting
C9 Engine for Caterpillar Built Machines Turbocharger Outlet Pressure Sensor - Remove and Install
C-10 Petroleum Engine Electronic Unit Injector Sleeve - Install
C-10 Petroleum Engine Turbocharger - Remove
C-10 Petroleum Engine Turbocharger - Disassemble
C-10 Petroleum Engine Turbocharger - Assemble
C9 Engine for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install