Blower Motor (Air Conditioner and Heater) - Install
Installation Procedure
- Install motor (20). Install the bolt and nut (19) .
Show/hide table
 | |
| Illustration 1 | g00361023 |
- Install cover (18) and three nuts (17) .
Show/hide table
 | |
| Illustration 2 | g00361022 |
- Install six bolts (16) .
Show/hide table
 | |
| Illustration 3 | g00361021 |
Show/hide table
 | |
| Illustration 4 | g00361020 |
- Connect four electrical connectors (15) .
Show/hide table
 | |
| Illustration 5 | g00361019 |
- Install coil assembly (14) and four bolts (13) .
Show/hide table
 | |
| Illustration 6 | g00361018 |
- Install two refrigerant hoses (11) and two heater hoses (12) .
- Connect electrical connector (10) .
- Install plastic cover (9) .
Show/hide table
 | |
| Illustration 7 | g00361017 |
- Install cover panel (8) and four bolts (7) .
Show/hide table
 | |
| Illustration 8 | g00361016 |
- Install two bolts (6) .
Show/hide table
 | |
| Illustration 9 | g00361015 |
- Install three bolts (5) .
Show/hide table
 | |
| Illustration 10 | g00361014 |
- Install the air filter and air filter cover (4). Tighten two screws (3) .
- Install air filter (2) on the left side of the cab. Close access door (1) .
Show/hide table
 | |
| Illustration 11 | g00361012 |
Show/hide table
 | |
| Illustration 12 | g00361013 |
- Evacuate the air conditioner system. Charge the air conditioner system. The correct charge is 2.0 kg (4.4 lb). Refer to Service Manual, SENR5664, "Air Conditioning and Heating Systems with R-134a Refrigerant" for the correct procedure. Refer to Special Publication, NEDG5065, "Air Conditioning Tools" for the correct tools.
- Close the engine hood.
End By: Install the seat. Refer to Disassembly and Assembly, "Seat - Remove and Install".
Caterpillar Information System:
C7 Engines for Caterpillar Built Machines Water Pump
950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Blower Motor (Air Conditioner and Heater) - Remove
2000/10/16 Grind a Chamfer Around the Exhaust Ports When New 194-8124 Sleeves Are Installed {1059}
Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467} Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467}
994D Wheel Loader Power Train Solenoid Valve (Transmission Clutch) - Test
2001/04/16 A New Spindle Is Available for Wheel Loaders, Wheel Tractors, and Landfill Compactors {4205}
988F Series II Wheel Loader Engine Supplement Fuel Filter and Fuel Filter Base (Primary) - Remove and Install - Removal and Installation in Machine
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 0144 - FMI 03
D7R Series II Track-Type Tractor Hydraulic System Implement Control Valve - Machines With a Ripper
D8R Series II Track-Type Tractor Engine Supplement Fumes Disposal - Remove and Install
973 Track-Type Loader Parking
973 Track-Type Loader Operation
994D Wheel Loader Power Train Speed Sensor (Transmission Output) - Adjust
902, 906 and 908 Compact Wheel Loaders Lifting and Tying Down the Machine
615C Series II Wheel Tractor-Scraper Hydraulic System Machine Preparation for Troubleshooting
D7R Series II Track-Type Tractor Hydraulic System Winch Control Valve
953C Track-Type Loader Power Train
953C Track-Type Loader Visual Inspection
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Payload Control System (PCS) - If Equipped
902, 906 and 908 Compact Wheel Loaders Capacities (Refill)
966F Wheel Loader and 966F Series II Wheel Loader Hydraulic System Pilot Hydraulic System
988G Wheel Loader Electrohydraulic System Gear Pump (Pilot and Braking)
AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 0144 - FMI 06
953C Track-Type Loader Troubleshooting