902, 906 and 908 Compact Wheel Loaders Caterpillar

Lifting and Tying Down the Machine

Usage:

906 6ZS

Weight and instructions are listed herein. This information is applicable to units that are manufactured by Caterpillar.

Show/hide table

Table 1
MACHINE WEIGHTS FOR NORTH AMERICAN APPLICATIONS
902	5300 kg (11685 lb)
906	6000 kg (13228 lb)

Show/hide table

Table 2
MACHINE WEIGHTS FOR EUROPEAN APPLICATIONS
902	5380 kg (11861 lb)
906	6080 kg (13404 lb)

Show/hide table

Table 3
MACHINE WEIGHTS
908	6301 kg (13911 lb)

Note: Weights may vary with different work tools.

For lifting objects, use properly rated cables and properly rated slings. Position the crane for a level machine lift.

Show/hide table




Illustration 1	g00614033

Show/hide table




Illustration 2	g00614040

The holes (1) in the loader and the hitch (2) are used as lifting points.

Spreader bar widths should be sufficient for preventing contact with the machine. The slings or cables should not exceed 15° from vertical when you lift the machine.

Show/hide table




Illustration 3	g00614041

Two front holes (3) and the hitch (2) are provided for tie-downs.

Install the tie-downs at several locations. Install the tie-downs for the bucket. Place chocks under the front wheels and under the rear wheels.

Check the appropriate laws that govern the weight of the load. Check the appropriate laws that govern the width of the load and the length of the load.

Consult your Caterpillar dealer for shipping instructions for your machine.

Caterpillar Information System:

994D Wheel Loader Power Train Speed Sensor (Transmission Output) - Adjust

950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Blower Motor (Air Conditioner and Heater) - Install

C7 Engines for Caterpillar Built Machines Water Pump

950G and 962G Wheel Loaders and IT62G Integrated Toolcarrier Machine Systems Blower Motor (Air Conditioner and Heater) - Remove

2000/10/16 Grind a Chamfer Around the Exhaust Ports When New 194-8124 Sleeves Are Installed {1059}

Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467} Special Instruction For Replacing a 173-7793 Droop Module With a 197-3531 Droop Module{4467}

994D Wheel Loader Power Train Solenoid Valve (Transmission Clutch) - Test

2001/04/16 A New Spindle Is Available for Wheel Loaders, Wheel Tractors, and Landfill Compactors {4205}

988F Series II Wheel Loader Engine Supplement Fuel Filter and Fuel Filter Base (Primary) - Remove and Install - Removal and Installation in Machine

AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 0144 - FMI 03

D7R Series II Track-Type Tractor Hydraulic System Implement Control Valve - Machines With a Ripper

D8R Series II Track-Type Tractor Engine Supplement Fumes Disposal - Remove and Install

615C Series II Wheel Tractor-Scraper Hydraulic System Machine Preparation for Troubleshooting

D7R Series II Track-Type Tractor Hydraulic System Winch Control Valve

953C Track-Type Loader Power Train

953C Track-Type Loader Visual Inspection

IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Payload Control System (PCS) - If Equipped

902, 906 and 908 Compact Wheel Loaders Capacities (Refill)

966F Wheel Loader and 966F Series II Wheel Loader Hydraulic System Pilot Hydraulic System

988G Wheel Loader Electrohydraulic System Gear Pump (Pilot and Braking)

AD30 and AD55 Underground Articulated Trucks Power Train Electronic Control System MID 027 - CID 0144 - FMI 06

953C Track-Type Loader Troubleshooting

988G Wheel Loader Braking System Gear Pump (Pilot and Braking)

988F Series II Wheel Loader Engine Supplement Fuel Filter and Fuel Filter Base (Secondary) - Remove and Install - Removal and Installation in Machine